Investigation of recast layer of non-conductive ceramic due to micro-EDM

QR Code

Investigation of recast layer of non-conductive ceramic due to micro-EDM

This paper presents the investigation of minimum recast layer of zirconium oxide (ZrO2) due to micro-EDM using EDM-3 synthetic oil as dielectric fluid and tungsten as the tool electrode with control parameters of rotational speed and gap voltage. The investigation was performed using multi-proces...

Full description

Bibliographic Details
Main Authors:	Mohamed, Abd. Rahman, Asfana, Banu, Ali, Mohammad Yeakub
Format:	Article
Language:	English English
Published:	Trans Tech Publications, Switzerland 2014
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/35540/ http://irep.iium.edu.my/35540/1/3.pdf http://irep.iium.edu.my/35540/4/35540_Investigation%20of%20recast%20layer%20of%20non-conductive%20ceramic%20due%20to%20micro-EDM.SCOPUSpdf.pdf

Similar Items

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode cooling on recast layers and micro crack in EDM of titanium
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Micro-electro discharge machining of nonconductive zirconia ceramic: investigation of MRR and recast layer hardness
by: Banu, Asfana, et al.
Published: (2014)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Investigation of taper angle in dry micro wire EDM
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Micro-edm for micro-channel fabrication on nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2014)

Investigation of the machinability of non-conductive zro2 with different tool electrodes in EDM
by: Moudood, M. A., et al.
Published: (2014)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

High aspect ratio micro-EDM drilling with nano surface finish
by: Ali , Mohammad Yeakub, et al.
Published: (2016)

Investigation of surface roughness in micro-EDM of nonconductive ZrO2 ceramic with powder mixed dielectric fluid
by: Sabur, Abdus, et al.
Published: (2015)

Investigation of vibration and surface roughness in micro milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Effect of micro-EDM parameters on material removal rate of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2011)

Geometrical integrity of microholes produced by micro-EDM
by: Ali, Mohammad Yeakub
Published: (2008)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Investigation of material removal characteristics in EDM of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2013)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Micro electro discharge machining of non-conductive ceramic using conductive powder mix dielectric fluid
by: Ali, Mohammad Yeakub, et al.
Published: (2016)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Influence of energy parameters of micro WEDM on kerf
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Optimization of EDM parameters for micro/meso fabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Near net shape machining by Micro-EDM and Micro-WEDM
by: Saleh, Tanveer, et al.
Published: (2019)

Dimensional accuracy of micro-electro discharge milling
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Investigation of optimum EDM die sinking parameters in micro dimple machining
by: Lee, Jie Ying, et al.
Published: (2022)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
by: Khan, Ahsan Ali, et al.
Published: (2013)

Investigation of burr formation in micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Developments in EDM process variables
by: Khan, Ahsan Ali, et al.
Published: (2011)

Investigation of finish cut of micro electro discharge milling for nano surface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Influence of thermal conductivity cf electrodes on EDM process parameters
by: Khan, Ahsan Ali, et al.
Published: (2012)

Investigation of vibration in micromilling with MQL: S/N ratio analysis
by: Hussin, Muhammad Shaffiq, et al.
Published: (2020)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic
by: Moudood, M. A., et al.
Published: (2014)

Empirical modelling of vibration in micro end milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Micro electro discharge machining of non-conductive ceramic
by: Ali, M., et al.
Published: (2018)

Exploration of EDM assisted CNT in micro machining using statistical approach
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Analysis of corner radius in dry micro WEDM
by: Chowdhury, Ahmed Ghalib Khan, et al.
Published: (2018)