Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic

QR Code

Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic

Electrical discharge machining (EDM) is a non-conventional machining process where materials are removed by the thermal energy exerted from series of electrical sparks. This process is applied for machining of non-conductive alumina (Al2O3). The workpiece is covered with the adhesive copper foil...

Full description

Bibliographic Details
Main Authors:	Moudood, M. A., Sabur, A., Ali, Mohammad Yeakub, Jaafar, Israd Hakim
Format:	Article
Language:	English English
Published:	Trans Tech Publications, Switzerland 2014
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/35539/ http://irep.iium.edu.my/35539/1/2.pdf http://irep.iium.edu.my/35539/4/35539_Effect%20of%20peak%20current%20on%20material%20removal%20rate_SCOPUS.pdf

Similar Items

Effect of gap voltage and pulse-on time on material removal rate for electrical discharge machining of Al2O3
by: Moudood, M. A., et al.
Published: (2015)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Investigation of the machinability of non-conductive zro2 with different tool electrodes in EDM
by: Moudood, M. A., et al.
Published: (2014)

Micro electro discharge machining of non-conductive ceramic
by: Ali, M., et al.
Published: (2018)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

Effect of micro-EDM parameters on material removal rate of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2011)

Effect of Micro-EDM Parameters on Material Removal Rate of Nonconductive ZrO2 Ceramic
by: Maleque, Md. Abdul, et al.
Published: (2014)

Micro electro discharge machining of nonconductive ceramic: the issue of spalling
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Electro-discharge machining of alumina: investigation of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Modelling of material removal rate in electro discharge machining of nonconductive ZrO₂ Ceramic with kerosene and EDM oil dielectric fluid / Abdus Sabur … [et al.]
by: Sabur, Abdus
Published: (2014)

Micro wire electrical discharge machining of tungsten carbide: analysis of material removal rate
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Micro electro discharge machining of non-conductive ceramic using conductive powder mix dielectric fluid
by: Ali, Mohammad Yeakub, et al.
Published: (2016)

Investigation of surface roughness in micro-electro discharge machining of nonconductive ZrO2 for MEMS application
by: Sabur, Abdus, et al.
Published: (2013)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining / Ahsan Ali Khan, Mohammad Yeakub Ali and Md. Mohafizul Haque
by: Khan, Ahsan Ali, et al.
Published: (2010)

Microstructural and process characterization on the electrical conductivity and electrical discharge machinability of Al2O3-based ceramic composites
by: Mebrahitom, A., et al.
Published: (2018)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Fabrication of micro filter by electro discharge machining
by: -, Abdus Sabur, et al.
Published: (2011)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Micro electro discharge machining of micropillar array: analysis of material removal rate
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Machining of ceramic materials: a review
by: Sabur, Abdus, et al.
Published: (2011)

Dry electrical discharge machining: an environmental friendly machining process
by: Ali, Mohammad Yeakub
Published: (2018)

Modelling of material removal rate in EDM of nonconductive ZrO2 ceramic by Taguchi method
by: Sabur, Abdus, et al.
Published: (2013)

Investigation of corner radius using micro wire electro discharge machine
by: Sabur, Abdus, et al.
Published: (2011)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Micro-edm for micro-channel fabrication on nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2014)

Experimental study of conventional wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)

Investigation on removal mechanism in catalytic aided electrical discharge machining of polycrystalline diamond
by: Ahmad, Muhammad Ariff Haikal
Published: (2019)

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Study of material removal rate and electrode wear ratio for micro electrical discharge milling of AISI 420 and Stavax ESR
by: Mohammad, Yeakub Ali, et al.
Published: (2009)

Micro-electro discharge machining of nonconductive zirconia ceramic: investigation of MRR and recast layer hardness
by: Banu, Asfana, et al.
Published: (2014)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Current research trends on dry, near-dry and powder mixed electrical discharge machining
by: Rahman Khan, Md. Ashikur, et al.
Published: (2011)

Current Research Trends on Dry, Near-Dry and Powder Mixed Electrical Discharge Machining
by: M. M., Noor, et al.
Published: (2011)

Micro wire electrical discharge machining of tungsten carbide: methodology and procedure
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Influence of nano powder mixed dielectric fluid on surface finish in micro electro discharge machining of zirconia
by: Ali, Mohammad Yeakub, et al.
Published: (2017)