Modeling large deformation and failure of expanded polystyrene crushable foam using LS-DYNA

QR Code

Modeling large deformation and failure of expanded polystyrene crushable foam using LS-DYNA

In the initial phase of the research work quasi-static compression tests were conducted on the expanded polystyrene (EPS) crushable foam for material characterisation at low strain rates (8.3x10-3~8.3x10-2 s-1) to obtain the stress strain curves. The resulting stress strain curves compared well with...

Full description

Bibliographic Details
Main Authors:	Shah, Qasim Hussain, Topa, Ameen
Format:	Article
Language:	English English
Published:	Hindawi Publishing Corporation 2014
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/35176/ http://irep.iium.edu.my/35176/1/foampaper.pdf http://irep.iium.edu.my/35176/4/35176_Modeling%20large%20deformation%20and%20failure.SCOPUS.pdf

Similar Items

LS-DYNA for beginners: an insight into Ls-Prepost and Ls-Dyna
by: Hussain Shah, Qasim, et al.
Published: (2012)

Investigation of energy absorption capabilities of compressed and uncompressed crushable foams
by: Shah, Qasim Hussain, et al.
Published: (2015)

From LS-PREPOST to LS-DYNA: an introduction: LS-Dyna for beginners with 13 step by step solved examples
by: Shah, Qasim Hussain, et al.
Published: (2011)

Effect of addendum parameters to the formability of aluminum AL 6303
by: , Afzeri, et al.
Published: (2011)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Mode I delamination simulation using LS-DYNA
by: Ibrahim, Mohamed S., et al.
Published: (2011)

Sintering and properties of dense manganese-doped calcium phosphate bioceramics prepared using sol-gel derived nanopowders
by: Sopyan, Iis, et al.
Published: (2011)

Numerical study on failure process of aluminium plate subjected to normal impact by hemispherical projectiles
by: Ibrahim, Mohd Norihan, et al.
Published: (2014)

Fabrication and characterizations of recycled aluminium-copper-cullet powder (AL-CU-CP) metal composite
by: Nuhu, Awwal Hussain
Published: (2020)

Role of mechanical alloying parameters on powders distribution of Al/Cu alloy and Al/Cu composite
by: Jamal, N. A., et al.
Published: (2014)

Micro-edm for micro-channel fabrication on nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2014)

Effect of micro-EDM parameters on material removal rate of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2011)

A Method and an Apparatus for Machining a Tool Steel
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Heat-assisted machining
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Modeling the effect of CNT concentration in dielectric fluid on EDM performance using neural network
by: Khan, Ahsan Ali, et al.
Published: (2016)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

The effects of sliding parameters on dry wear characteristics of Ti-6Al-4V alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2015)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Design and development of a versatile ice clamping system
by: Bahar, Rubina, et al.
Published: (2014)

Effect of gap voltage and pulse-on time on material removal rate for electrical discharge machining of Al2O3
by: Moudood, M. A., et al.
Published: (2015)

Investigation of surface roughness in micro-EDM of nonconductive ZrO2 ceramic with powder mixed dielectric fluid
by: Sabur, Abdus, et al.
Published: (2015)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Effect of exfoliated graphene defects on thermal conductivity of water based graphene nanofluids
by: Rahat, Arifutzzaman, et al.
Published: (2018)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Dimensional accuracy of micro-electro discharge milling
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool
by: Rashid, Mohammed Abdur N., et al.
Published: (2018)

Experimental investigation and effective medium approximation of thermal conductivity of water based exfoliated Graphene nanofluids
by: Arifutzzaman, A. K. H. A. Ma, et al.
Published: (2018)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)