MEMS and EFF Technology based micro connector for future miniature devices

QR Code

MEMS and EFF Technology based micro connector for future miniature devices

The development of a miniature; size, light and high performance electronic devices; has been accelerated for further development. In commercial stamping method, connector pitch size (radius) is more than 300μm due to its size limitation. Therefore, the stamped contact hertz stress becomes lower...

Full description

Bibliographic Details
Main Authors:	Bhuiyan, Md. Moinul Islam, Rashid, Muhammad Mahbubur, Alamgir, Tarik Bin, Bhuiyan, Munira, Kajihara, Masanori
Format:	Proceeding Paper
Language:	English English
Published:	2013
Subjects:	TA165 Engineering instruments, meters, etc. Industrial instrumentation
Online Access:	http://irep.iium.edu.my/33343/ http://irep.iium.edu.my/33343/1/2129_MEMS_and_EFF_Technology_based_Micro_Connector_for.pdf http://irep.iium.edu.my/33343/2/ICOM13_Programme_Book.pdf

Similar Items

MEMS and EFF technology based micro connector for future miniature devices
by: Bhuiyan, Moinul, et al.
Published: (2013)

Design and fabrication stable LNF contact for future IC application
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2013)

Development and optimization of a low normal force contact
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2013)

A low normal force contact using photolithography and Ni-Co electro fine forming technology
by: Bhuiyan, Moinul, et al.
Published: (2009)

Development of robotic arm plotter for disable people
by: Bhuiyan, Moinul, et al.
Published: (2014)

Design and Implementation of Fuzzy Based Person Following Mobile Robot1
by: Rashid, Muhammad Mahbubur, et al.
Published: (2012)

Design and development of a smart window blind controlling system
by: Bhuiyan, Moinul, et al.
Published: (2014)

Development of optical switch using SMA coil and magnetic latch
by: Bhuiyan, Md. Moinul Islam, et al.
Published: (2003)

LNF Micro-Contact using MEMS and EFF Technology
by: Bhuiyan, Moinul, et al.
Published: (2013)

Design and optimization of a micro capacitive pressure sensor
by: Tahmasebpour, Kamyar, et al.
Published: (2013)

Development of an angle sensor using optical polarizer
by: Rana, M. M., et al.
Published: (2015)

Pulsed magnetic flux leakage techniques for crack detection and characterisation
by: Sophian, Ali, et al.
Published: (2006)

Data fusion for defect characterisation using a dual probe system
by: Edwards, R.S., et al.
Published: (2008)

A feature extraction technique based on principal component analysis for pulsed Eddy current {NDT}
by: Sophian, Ali, et al.
Published: (2003)

Reduction of lift-off effects for pulsed eddy current NDT
by: Tian, Gui Yun, et al.
Published: (2005)

Feature extraction and selection for defect classification of pulsed eddy current NDT
by: Chen, Tianlu, et al.
Published: (2008)

Defect classification using a new feature for pulsed eddy current sensors
by: Tian, Gui Yun, et al.
Published: (2005)

Dual EMAT and PEC non-contact probe: applications to defect testing
by: Edwards, R.S., et al.
Published: (2006)

Optical thermal imaging for breast cancer diagnosis
by: Zubir, Nazira, et al.
Published: (2016)

Tendon bioreactor
by: Zubir, Nazira, et al.
Published: (2016)

Electrochemical biosensor : amperometric – glucose sensor
by: Zubir, Nazira
Published: (2015)

Setting up a new Radiology Center Technology for improvement : Data mining (Image Mining Technique)
by: Zubir, Nazira
Published: (2016)

A novel signal diagnosis technique using pseudo complex-valued autoregressive technique
by: Aibinu, Abiodun Musa, et al.
Published: (2011)

EMC 201(3) - MEASUREMENT AND INSTRUMENTATION OKT-NOV 07.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2007)

Wattmeter reading with the range of IoT's communication
by: Azmi, NorIskandar, et al.
Published: (2020)

IoT based black box for vehicles
by: Aldholay, Mohammed Hussein Hassan, et al.
Published: (2020)

IoT and LoRaWAN
by: Ashraf, Ahmed, et al.
Published: (2020)

Effect of soaking time to the bending strength of porcelain with palm oil fuel ash
by: Noh, Mohamad Zaky, et al.
Published: (2018)

Sensor material characterisation for magnetometer application
by: Zinal, Nabiah
Published: (2004)

Comparison machining performance of Al2 O3 , ZTA and ZTA doped Cr2 O3 cutting tools on AISI 1045
by: T., Norfauzi, et al.
Published: (2019)

Development of groundwater filtration system using multiseries media
by: Abdul Aziz, Nor Izzah
Published: (2022)

Intelligent control of grain drying process using fuzzy logic controller
by: Mansor, Hasmah, et al.
Published: (2010)

Design and development of Multipurpose Educational and Research Platform (MERP) for learning control & IOT technologies
by: Embong, Abd Halim, et al.
Published: (2019)

Device characteristics of carbon nanotube transistor fabricated by direct growth method
by: Inami, Nobuhito, et al.
Published: (2008)

Thermal properties of polymer materials in laser sintering process
by: Pham, Duc Trung, et al.
Published: (2011)

Development of a high hertz-stress contact for conventional batch production using a unique scribing technology
by: Bhuiyan, Moinul, et al.
Published: (2013)

Effect of nanopolyacrylate and natural rubber latex on asphalt binder and mixture performance / Ekarizan Shaffie
by: Shaffie, Ekarizan
Published: (2018)

Mode I stress intensity factor for a cracked plate with an integrated piezoelectric actuator
by: Abuzaid, Ahmed, et al.
Published: (2015)

Finite element simulation of electro-mechanical impedance technique
by: Tahmasebpour, Kamyar, et al.
Published: (2015)

EPE 481 – Industrial Ergonomics (Ergonomik Industri)
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2024)