Cooling of motorcyclist helmet with thermoelectric module

QR Code

Cooling of motorcyclist helmet with thermoelectric module

This paper deals with the development of cooling system for motorcycle helmet using thermoelectric technology. The system consists mainly of a heat sink and thermoelectric module. When electrical voltage is applied to the thermoelectric module, it will create a temperature difference across the ther...

Full description

Bibliographic Details
Main Authors:	Hrairi, Meftah, Abdullah, Abdullah F., Ahmed, Mirghani Ishak
Format:	Article
Language:	English
Published:	IDOSI Publications 2013
Subjects:	TJ163.26 Energy conservation TJ807 Renewable energy sources
Online Access:	http://irep.iium.edu.my/32057/ http://irep.iium.edu.my/32057/1/16.pdf

Similar Items

Development and performance testing of a light weight portable solar rice cooker in rural areas of Bangladesh
by: Ahamed, R., et al.
Published: (2014)

A solar assisted heat pump system for desalination
by: Amin, Zakaria Mohd., et al.
Published: (2011)

An active cooling system for photovoltaic module
by: Teo, H. G., et al.
Published: (2012)

Investigation of aluminum heat sink design with thermoelectric generator
by: Mohiuddin, A. K. M., et al.
Published: (2017)

A review study on the effect of glass envelope, working fluid and geometry contributions for the receiver on performance of parabolic trough collector (PTC)
by: Abbas, Mohammed Saad, et al.
Published: (2018)

Optimization of a cooling system in data centers
by: Ali, Maisarah, et al.
Published: (2012)

Waste heat recovery in heat pump systems: solution to reduce global warming
by: Baradey, Yehya, et al.
Published: (2015)

Optimization of cooling systems in data centre by computational fluid dynamics model and simulation
by: Romadhon, Rahmat, et al.
Published: (2009)

Effect of periodic drying on energy utilization, product quality, and drying time
by: Baradey, Yehya, et al.
Published: (2017)

A triangular double layer microchannel heat sink: effect of parallel and counter flow
by: Manaf, Hazli, et al.
Published: (2014)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

Numerical analysis of heat transfer and nanofluid flow in a triangular duct with vortex generator: two-phase model
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Seder, Islam M.F., et al.
Published: (2014)

Control of ideally expanded and under expanded nozzle flows with micro jets
by: G M, Fharukh Ahmed, et al.
Published: (2016)

Hydrocarbons as alternative refrigerants in domestic refrigerators
by: S, Parashurama, et al.
Published: (2019)

Thermo-mechanical analysis and estimation of turbine blade tip clearance of a small gas turbine engine under transient operating conditions
by: Kumar, Rahul, et al.
Published: (2020)

Analysis of solar desalination system using heat pump
by: Amin, Zakaria Mohd., et al.
Published: (2015)

Active control of suddenly expanded flow
by: Khan, Sher Afghan, et al.
Published: (2000)

Modelling and validation of proton exchange membrane fuel cell (PEMFC)
by: Mohiuddin, A. K. M., et al.
Published: (2018)

Performance analyses of horizontal axis wind turbines using QBlade
by: Zuhdi, Amirul Hakim, et al.
Published: (2017)

Validated analytical modeling of diesel engine regulated exhaust CO emission rate
by: Faris, Waleed Fekry, et al.
Published: (2016)

Comparative heat transfer analysis in different mini-channel heat sinks
by: Afzal, Asif, et al.
Published: (2017)

Energy harvesting from aerodynamic instabilities: Current prospect and future trends
by: Bashir, Musavir, et al.
Published: (2018)

Numerical investigation of semiempirical relations representing the local Nusselt number magnitude of a pin fin heat sink
by: Siddiqi, Mohammad Umar, et al.
Published: (2019)

On numerical investigation of semi-empirical relations representing local nusselt number at lower nozzle-target spacing’s
by: Siddique, Mohd Umair, et al.
Published: (2019)

Threaded spikes for bluff body base flow control
by: Khan, Sher Afghan, et al.
Published: (2019)

Investigation on producing silica from rice husk biomass
by: Uddin, M.N., et al.
Published: (2018)

Magnetically plucked piezoelectric energy harvester via hybrid kinetic motion
by: Azam, Huda, et al.
Published: (2019)

A desalination system utilizing solar ambient and waste energy
by: Hawlader, M N A, et al.
Published: (2011)

Transport analysis of an Air Gap Membrane Distillation (AGMD) process
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2011)

Reconstruction and electronic properties of interface between carbon nanotubes and ferromagnetic co electrodes
by: Cuong, Nguyen Tien, et al.
Published: (2012)

Combined water and power plant (CWPP) — a novel desalination technology
by: Mahbub, Fazle, et al.
Published: (2009)

PERFORMANCE OF A SOLAR INTEGRATED HEAT PUMP AIR-CONDITIONER, WATER HEATER AND DRYER
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2008)

Performance evaluation of a mechanical vapor compression desalination system
by: Bahar, Rubina, et al.
Published: (2004)

Economic evaluation of a solar water heating system
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (1987)

Pretreatment of seawater: Results of pilot trials in Singapore
by: Chua, K T, et al.
Published: (2003)

Pro-environmentalists behavioural assessment towards energy conservation among Malaysian university students
by: Mohamad Kawi, Nur Farisha Husna, et al.
Published: (2021)

Energy saving patterns of personnel behaviour in Malaysian office
by: Ishak, Mohd Hafizal, et al.
Published: (2018)

EMK 402 - SISTEM PENUKARAN TENAGA OKT-NOV 1994.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (1994)