The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel

QR Code

The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel

The effect of various percentages of palm oil diesel (POD) fuel contaminated lubricants on the wear charactefis:ics of east irons during sliding contact was investigated. This was done on three types of cast iron, namely spheroidal graphite, flake graphite and chilled cast iron against a mild steel...

Full description

Bibliographic Details
Main Authors:	Masjuki, H.H., Maleque, Md. Abdul
Format:	Article
Language:	English
Published:	Elsevier BV 1996
Subjects:	TA170 Environmental engineering. Sustainable engineering TN600 Metallurgy
Online Access:	http://irep.iium.edu.my/29639/ http://irep.iium.edu.my/29639/1/P1_1996.pdf

Similar Items

Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
by: Maleque, Md. Abdul, et al.
Published: (1998)

Wear behavior of aluminium modified cast iron in comparison with conventional gray cast iron
by: Maleque, Md. Abdul, et al.
Published: (2018)

The tribological behaviour of Fe-C-Al cast iron – effect of temperature
by: Maleque, Md. Abdul, et al.
Published: (2013)

Investigation of the anti-wear characteristics of palm oil methyl ester using a four-ball tribometer test
by: Maleque, Md. Abdul, et al.
Published: (1997)

Wear surface characteristics study of tribo-materials under palm oil methyl ester added lubricant
by: Maleque, Md. Abdul, et al.
Published: (2002)

Wear, performance and emissions of a two-stroke engine running on palm oil methyl ester blended lubricant
by: Masjuki, H.H., et al.
Published: (1996)

Wear properties of Fe-C-Al cast iron and conventional cast iron - a comparative study
by: Maleque, Md. Abdul
Published: (2011)

Experimental investigation on system performance using palm oil as hydraulic fluid
by: Wan Nik, W.B., et al.
Published: (2007)

Sliding wear of SiC reinforced duplex stainless steel via TIG torch surface melting technique
by: Maleque, Md. Abdul, et al.
Published: (2020)

Surface modification of mild steel using tungsten inert gas torch surface cladding
by: Dyuti, S., et al.
Published: (2010)

Lubricated wear behaviour of SiC reinforcement on TI-6AL-4V alloy based on Taguchi approach
by: Maleque, Md. Abdul, et al.
Published: (2016)

Friction Coefficient and Wear Rate of Copper and Aluminum Sliding against Mild Steel
by: Nuruzzaman, D. M., et al.
Published: (2012)

Alumina recovery from industrial waste: study on the thermal, tensile and wear properties of polypropylene/alumina nanocomposites
by: Sofian, Anis Sofia, et al.
Published: (2019)

Modelling aspect of corrosive wear under biodiesel
by: Adebisi, Adetayo A., et al.
Published: (2011)

Performance, emissions and wear characteristics of an indirect injection diesel engine using coconut oil blended fuel
by: Masjuki, H.H., et al.
Published: (2001)

The effect of intercritical heat treatment on the mechanical properties of AISI 3115 steel
by: Maleque, Md. Abdul, et al.
Published: (2004)

Utilization of low-grade iron ore in ammonia decomposition
by: Othman, Nur Ezzah Faezah, et al.
Published: (2016)

Treatment of iron ore using biomass waste for ironmaking
by: Mohamad Selamat, Norfazilah, et al.
Published: (2011)

Wear and corrosion of composite coated AISI 4340 steel exposed to jatropha curcas biodiesel
by: Maleque, Md. Abdul, et al.
Published: (2014)

Wear behavior of modified surface layer produced by TIG melting of preplaced Ti powder in nitrogen environment
by: Mridha, Shahjahan, et al.
Published: (2011)

Enhancement magnetic properties of Malaysian iron ore by biomass treatment
by: Purwanto, Hadi
Published: (2014)

Biotar ironmaking using wooden biomass and nanoporous iron ore
by: Hata, Yuichi, et al.
Published: (2009)

Reduction of iron ore/empty fruit bunch char briquette composite
by: Yunus, Nurul Azhani, et al.
Published: (2013)

Composite brake rotor: energy savings and wear performance
by: Maleque, Md. Abdul
Published: (2015)

Utilization of palm oil biomass for treatment of low grade Malaysian iron ore
by: Hadi Puwanto, purwanto
Published: (2014)

Phase formation during reduction of iron sand with soda ash flux addition
by: , Pramusanto, et al.
Published: (2011)

Effect of temperature on the wear properties of alloy steel under jatropha curcas biodiesel
by: Shaufe, N. A., et al.
Published: (2015)

Wear behaviour optimization of TIG parameters on wear behavior of sic embedded coatings using Taguchi approach
by: Maleque, Md. Abdul, et al.
Published: (2016)

Wear mechanisms map of CNT-Al nano-composite
by: Abdullahi, U., et al.
Published: (2013)

Effect of energy input on wear behaviour of SiC surface modified layer duplex stainless steel
by: Paijan, Lailatul Harina, et al.
Published: (2017)

Experimental Investigation of Friction Coefficient and Wear Rate of Stainless Steel 304 Sliding against Smooth and Rough Mild Steel Counterfaces
by: Chowdhury, M. A., et al.
Published: (2013)

Enhancement of magnetic properties of Malaysian iron ore by reduction roasting using oil palm empty fruit bunch
by: Purwanto, Hadi, et al.
Published: (2014)

Effect of charcoal derived from oil palm empty fruit bunch on the sinter characteristics of low grade iron ore
by: Hadi, Purwanto, et al.
Published: (2018)

Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Microstructural aspects of wear behaviour of TiC coated low alloy steel
by: Md Idriss, A. N., et al.
Published: (2016)

Effect of reduction roasting by using bio-char derived from empty fruit bunch on the magnetic properties of Malaysian iron ore
by: Purwanto, Hadi, et al.
Published: (2014)

Topography orientation effects on friction and wear in sliding DLC and steel contacts, part 3: Experiments under dry and lubricated conditions
by: Holmberg, Kenneth, et al.
Published: (2021)

Influence of iron (II) oxide nanoparticle on biohydrogen production in thermophilic mixed fermentation
by: Engliman, Nurul Sakinah, et al.
Published: (2017)

Physical property of multi walled carbon nanotube reinforced aluminium nano composite
by: Maleque, Md. Abdul
Published: (2013)

Novel activated Ni-P-hBN composite powder for efficient solid lubricant coating application
by: Maleque, Md. Abdul
Published: (2015)