Feasibility of local manufacturer of spares for fertilizer factories of Bangladesh-a case study

QR Code

Feasibility of local manufacturer of spares for fertilizer factories of Bangladesh-a case study

Fertilizer factories in Bangladesh depend almost entirely on imported spare parts, which are very costly, involve foreign currency consumption and long lead time for procurement. This leads to huge inventory costs and lot of spares are kept in reserve in the fear of factory shut downs. As an attempt...

Full description

Bibliographic Details
Main Authors:	Amin, A. K. M. Nurul, Ihsanul Karim , Syed Md.
Format:	Article
Language:	English
Published:	1990
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/29504/ http://irep.iium.edu.my/29504/1/1990_Feasibility_of_local_manufacturer_of_spares_for_fertilizer.pdf

Similar Items

A case study on design and manufacture of tilting pad thrust bearing for steam turbine of fertilizer factories
by: Amin, A. K. M. Nurul, et al.
Published: (1996)

Design and manufacture of a ten ton capacity wedge jack
by: Azim, M. Anwarul, et al.
Published: (1989)

A feasibility study on low temperature thermochemical treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
by: Haruman, Esa, et al.
Published: (2011)

Investigation of the mechanism of chatter formation during metal cutting process
by: Amin, A. K. M. Nurul
Published: (1983)

Influence of the characteristics of Machine-Tool-Fixture-Work (MTFW) system on chatter
by: Amin, A. K. M. Nurul
Published: (1985)

Influence of work material, cutting conditions and rigidity of tool holders on machine tool chatter
by: Amin, A. K. M. Nurul
Published: (1992)

Criteria for determining machinability and techniques of improving machinability of steel and alloys
by: Amin, A. K. M. Nurul
Published: (1993)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Investigation of the influence of different parameters on chatter arising during metal cutting process
by: Amin, A. K. M. Nurul, et al.
Published: (1999)

The effect of preheating of work on chatter during end milling of medium carbon steel performed on a Vertical Machining Center (VMC)
by: Amin, A. K. M. Nurul, et al.
Published: (2003)

Experimental determination of optimum cutting conditions in turning low alloyed steel with cemented carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Improved tool life in end milling ti-6al-4v through workpiece preheating
by: Ginta , Turnad L., et al.
Published: (2009)

Experimental investigation of chip tool contact process and determination of optimum cutting speed for steel of any composition
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

Heat-assisted machining
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Surface integrity in end milling titanium alloy Ti6Al4V under heat assisted machining
by: Ginta, Turnad Lenggo, et al.
Published: (2013)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Heat assisted machining of metals and alloys using induction heating method
by: Amin, A. K. M. Nurul, et al.
Published: (2013)

Influence of the instability of chip formation and preheating of work on tool life in maching high temperature resistant steel and titanium alloys
by: Amin, A. K. M. Nurul, et al.
Published: (1986)

Investigation of the influence of chatter on tool wear
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Investigation of chatter arising in Machine Tool-Fixture Work (MTFW) system during turning
by: Amin, A. K. M. Nurul, et al.
Published: (1994)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

A Method and an Apparatus for Machining a Tool Steel
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Investigation of the physical causes of improved machinability of steel alloyed with calcium
by: Amin, A. K. M. Nurul, et al.
Published: (1984)

Development of mathematical model for chip serration frequency in turning of stainless steel 304 using RSM
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Application of permanent magnets for chatter control in end milling of titanium alloy Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

A new experimental approach to determination of critical depth in high speed machining of soda-lime glass
by: Mahmud, M.A, et al.
Published: (2012)

Influence of magnetic field on reduction chatter and of surface roughness in end milling of Titanium Alloy - Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Optimization of surface roughness in end milling of titanium alloy TI-6AL-4V under the influence of magnetic field from permanents magnets
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Surface roughness model for high speed end milling of soda lime glass using carbide coated tools with compressed air blowing
by: Mahmud, M. A., et al.
Published: (2012)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Effectiveness of uncoated WC-Co and PCD inserts in end milling of aluminum silicon carbide (AlSiC)
by: M. K., Nor Khairusshima, et al.
Published: (2007)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

Identification of instabilities of the chip formation and it's prediction model during end milling of medium carbon steel (S45C)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Modeling and optimization of surface roughness and vibration amplitude in heat assisted end milling of SKD 11 tool steel using ball nose tool
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon
by: Amin, A. K. M. Nurul, et al.
Published: (2012)