Design and manufacture of a ten ton capacity wedge jack

QR Code

Design and manufacture of a ten ton capacity wedge jack

A Wedge Jack of relatively small dimensions (300 x 100 x 50 mm), but extremely high load carrying capacity (10 tons) has been designed for precision lifting of turbine shaft and its bearing cases for their proper alignment at Ghorasal Power Plant. The work was unique of its kind in Bangladesh, since...

Full description

Bibliographic Details
Main Authors:	Azim, M. Anwarul, Amin, A. K. M. Nurul, Khan, Ahsan Ali
Format:	Article
Language:	English
Published:	1989
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/29502/ http://irep.iium.edu.my/29502/1/1989_Design_and_manufacturer_of_a_ten_ton_capacity_wedge_jack.pdf

Similar Items

A case study on design and manufacture of tilting pad thrust bearing for steam turbine of fertilizer factories
by: Amin, A. K. M. Nurul, et al.
Published: (1996)

Feasibility of local manufacturer of spares for fertilizer factories of Bangladesh-a case study
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Modeling and analysis of MRR, EWR and surface roughness in EDM milling through response surface methodology
by: Asif Iqbal, A.K.M., et al.
Published: (2010)

The effects of process variables on the hardness of nitrided 3% chromium steel
by: Mridha, Shahjahan, et al.
Published: (2008)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Design and development of Acrylic Die for producing wax pattern to gabricate hip bone joint
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Improving tool life using cryogenic cooling
by: Khan, Ahsan Ali, et al.
Published: (2008)

Investigation on structure and properties of brass casting
by: Haque, Md. Mohafizul, et al.
Published: (2008)

Performance of different abrasive materials during abrasive water jet machining of glass
by: Khan, Ahsan Ali, et al.
Published: (2007)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrodes for EDM
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2011)

Determination of influential factors on EDMed surface properties using Plackett-Burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Determination of influential factors on edmed surface properties using plackett-burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

A study on abrasive water jet machining of aluminum with garnet abrasives
by: Khan, Ahsan Ali, et al.
Published: (2005)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Role of current, voltage and spark on-time on electrode material migration during EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during edm of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on recast layers and micro crack in EDM of titanium
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during EDM of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)