Experimental determination of optimum cutting conditions in turning low alloyed steel with cemented carbide tool

QR Code

Experimental determination of optimum cutting conditions in turning low alloyed steel with cemented carbide tool

A scientific method has been developed to determine the optimum values of machining variable, which does not involve costly and precision measuring instruments. On the basis of the existing theories and present experimental results the following have been established. Tool wear and cutting force are...

Full description

Bibliographic Details
Main Authors:	Amin, A. K. M. Nurul, Sankar, Roy
Format:	Article
Language:	English
Published:	1987
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/29500/ http://irep.iium.edu.my/29500/1/1987_Experimental_determination_of_optimum_cutting_conditions_i.pdf

Similar Items

Experimental investigation of chip tool contact process and determination of optimum cutting speed for steel of any composition
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool
by: Rashid, Mohammed Abdur N., et al.
Published: (2018)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Influence of work material, cutting conditions and rigidity of tool holders on machine tool chatter
by: Amin, A. K. M. Nurul
Published: (1992)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Influence of the instability of chip formation and preheating of work on tool life in maching high temperature resistant steel and titanium alloys
by: Amin, A. K. M. Nurul, et al.
Published: (1986)

A new approach of applying cryogenic coolant in turning AISI 304 stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Development of mathematical model for chip serration frequency in turning of stainless steel 304 using RSM
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Investigation of chatter arising in Machine Tool-Fixture Work (MTFW) system during turning
by: Amin, A. K. M. Nurul, et al.
Published: (1994)

Investigation of the physical causes of improved machinability of steel alloyed with calcium
by: Amin, A. K. M. Nurul, et al.
Published: (1984)

Criteria for determining machinability and techniques of improving machinability of steel and alloys
by: Amin, A. K. M. Nurul
Published: (1993)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

A Method and an Apparatus for Machining a Tool Steel
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface roughness model for high speed end milling of soda lime glass using carbide coated tools with compressed air blowing
by: Mahmud, M. A., et al.
Published: (2012)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Dry machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2012)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Energy cost modeling for high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Dissimilar materials laser welding characteristics of stainless steel and titanium alloy
by: Mohid, Zazuli, et al.
Published: (2014)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Modeling and optimization of surface roughness and vibration amplitude in heat assisted end milling of SKD 11 tool steel using ball nose tool
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

New approach in cost structuring of high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

Investigation on the surface finish, MRR and the surface damage during the EDM of tungsten carbide
by: Khan, Ahsan Ali, et al.
Published: (2011)

Dry machining of T6061 aluminium alloy using titanium nitride (TiN)and titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Influence of sintering temperature on density, hardness, shrinkage and microstructure of alumina-zirconia cutting tool
by: A. A., Anis, et al.
Published: (2021)

Minimum Quantity Lubrication (MQL) and its effect on tool wear during miniature drilling: an experimental study
by: Mohamad, Norsalawani, et al.
Published: (2016)

A study on material removal rate during EDM with tantalum carbide-copper compacted electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

Role of mechanical alloying parameters on powders distribution of Al/Cu alloy and Al/Cu composite
by: Jamal, N. A., et al.
Published: (2014)

Influence of chatter of VMC arising during end milling operation and cutting conditions on quality of machined surface
by: A.K.M, N. Amin, et al.
Published: (2001)