Micro-drilling of metallic materials for microsystems technology

QR Code

Micro-drilling of metallic materials for microsystems technology

This research project focused on the use of micro-EDM to create micro-holes with different aspect ratio (depth/diameter). It examined the influence of various factors on the final accuracy in EDM micro drilling. In particular, the main parameters affecting the aspect ratio, vertical side wall, si...

Full description

Bibliographic Details
Main Author:	Ali, Mohammad Yeakub
Format:	Monograph
Language:	English
Published:	Research Management Center, IIUM 2008
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/28923/ http://irep.iium.edu.my/28923/1/097_EDW-18_2008_Full_report.pdf

Similar Items

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

High aspect ratio micro-EDM drilling with nano surface finish
by: Ali , Mohammad Yeakub, et al.
Published: (2016)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Geometrical integrity of microholes produced by micro-EDM
by: Ali, Mohammad Yeakub
Published: (2008)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Polymeric micro-fluidic channel by hot embossing
by: Mohammad, Amar Sami, et al.
Published: (2006)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Mass-replication of micro-components
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Experimental study of electrical discharge drilling of stainless steel UNS S30400
by: Hanash, Ebrahim, et al.
Published: (2018)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Fabrication of three dimensional micro-components – A review
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Investigation of recast layer of non-conductive ceramic due to micro-EDM
by: Mohamed, Abd. Rahman, et al.
Published: (2014)

Developing a prototype micro hot embossing setup
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Empirical modelling of vibration in micro end milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Effect of drill geometry of uncoated tool when drilling titanium alloy, Ti-6Al-4V
by: Rashiddy Wong, Freddawati
Published: (2008)

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Micro/Meso Mechanical Manufacturing (M4): opportunities and challenges: a review
by: Reyad, Mehfuz, et al.
Published: (2006)

Drilling of bone: Effect of drill bit geometries on thermal osteonecrosis risk regions
by: Mohd Faizal, Ali Akhbar, et al.
Published: (2019)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

Finite Element Study on The Effect of Substrate Properties in Micro-cutting Thin Workpiece Materials
by: Saptaji, Kushendarsyah, et al.
Published: (2016)

Investigation of material removal characteristics in EDM of nonconductive ZrO2 ceramic
by: Sabur, Abdus, et al.
Published: (2013)

Optimization of EDM parameters for micro/meso fabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Statistical Analysis of Deep Drilling Processs Conditions Using Vibrations and Force Signals
by: Hazwan, Syafiq, et al.
Published: (2015)

Statistical Analysis of Deep Drilling Process Conditions Using Vibrations and Force Signals
by: Hazwan, Syafiq, et al.
Published: (2016)

Investigation of taper angle in dry micro wire EDM
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic
by: Moudood, M. A., et al.
Published: (2014)

Focused ion beam micromachining of mems
by: Ali, Mohammad Yeakub
Published: (2008)

Nanopillar Array for Cell Culture Dish
by: Ali, Mohammad Yeakub
Published: (2011)