Biodegradability analysis of KBF reinforced poly(lactic acid) biocomposites

QR Code

Biodegradability analysis of KBF reinforced poly(lactic acid) biocomposites

Poly(lactic acid) (PLA) and kenaf bast fiber (KBF) were melt-blended using brabender into films in the PLA/KBF ratios of 100/0, 90/10, 70/30 and 50/50 for natural soil burial test. This formulation was used to study the biodegradability of PLA and PLA/KBF biocomposites. It was found that the decompo...

Full description

Bibliographic Details
Main Authors:	Othman, Maizatulnisa, Ibrahim, Nor Azowa, Ruzaidi, Che Mohd, Mohd Nazarudin, Zakaria, Halim, Zahurin
Format:	Article
Language:	English English
Published:	Trans Tech Publications, Switzerland 2012
Subjects:	TA401 Materials of engineering and construction TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/28858/ http://irep.iium.edu.my/28858/1/Biodegradability_Analysis_of_KBF_Reinforced_Poly%28lactic_Acid%29_Biocomposites.pdf http://irep.iium.edu.my/28858/4/28858_Biodegradability%20analysis%20of%20KBF%20reinforced_SCOPUS.pdf

Similar Items

Mechanical performance of montmorillonite dispersed jute reinforced composite
by: Muhammad Hasibul , Hasan, et al.
Published: (2015)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Biodegradation properties of poly (Lactic) acid reinforced by kenaf fibers
by: Surip, S.N. Surip, et al.
Published: (2016)

Wear characteristics of multiple particle size silicon carbide reinforced aluminium composite
by: Abdulmumin, Adebisi Adetayo, et al.
Published: (2015)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

A study on material removal rate during EDM with tantalum carbide-copper compacted electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of EDM of mild steel with Ta-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of current, spark on-time and off-time on electrode wear during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

A comparative study on work surface hardness EDMed by Ta-C powder compacted and copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2012)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Role of current, voltage and spark on-time on electrode material migration during EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

Performance of PM compacted Cu-TaC electrodes during EDM
by: Mohammed, Baba Ndaliman, et al.
Published: (2011)

Effect of nanoparticles on wettability of nanocoating on carbon steel
by: Johari, Norhasnidawani, et al.
Published: (2016)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

A study of parameters relationship to backcutting phenomena during high speed end milling of AISI H13
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Statistical approach to modeling & optimization of surface roughness in high speed end milling of silicon with diamond coated tools
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Modeling the effect of CNT concentration in dielectric fluid on EDM performance using neural network
by: Khan, Ahsan Ali, et al.
Published: (2016)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Surface roughness optimization in end milling of stainless steel AISI 304 with uncoated WC-Co insert under magnetic field
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Sintering and properties of dense manganese-doped calcium phosphate bioceramics prepared using sol-gel derived nanopowders
by: Sopyan, Iis, et al.
Published: (2011)

Energy cost modeling for high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)