Dry machining of T6061 aluminium alloy using titanium nitride (TiN)and titanium carbonitride (TiCN) coated tools

QR Code

Dry machining of T6061 aluminium alloy using titanium nitride (TiN)and titanium carbonitride (TiCN) coated tools

Dry machining is a clean machining process and it will be considered as a necessity for manufacturing industries in future.Dry machining is environmental friendly and safe to be performed. Regardless of decreasing tool life due to lack of lubricants, choosing dry machining over wet machining may be...

Full description

Bibliographic Details
Main Authors:	Mohamed Ariff, Tasnim Firdaus, Paimin, Muhamad Fahmie, Hassan, Abdirahman
Format:	Article
Language:	English
Published:	Trans Tech Publications Ltd., Switzerland 2013
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/28624/ http://irep.iium.edu.my/28624/1/AMM.284-287.291.pdf

Similar Items

Dry machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2012)

Dry machining of brass using titanium carbonitride (TiCN) coated tool
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

An experimental investigation of TiCN tool life and tool wear in turning of titanium / Muhamad Anwar Salehudin
by: Salehudin, Muhamad Anwar
Published: (2016)

Application of permanent magnets for chatter control in end milling of titanium alloy Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Surface integrity in end milling titanium alloy Ti6Al4V under heat assisted machining
by: Ginta, Turnad Lenggo, et al.
Published: (2013)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

Influence of magnetic field on reduction chatter and of surface roughness in end milling of Titanium Alloy - Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Optimization of surface roughness in end milling of titanium alloy TI-6AL-4V under the influence of magnetic field from permanents magnets
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Feasibility and performance of TiCN-based patch antennas for microwave antenna applications
by: Mohamad Ashry, Jusoh, et al.
Published: (2024)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Assessment of machining cost for end-milling of Ti-6Al-4V titanium alloy through RSM-based parametric model
by: Karim, A.N. Mustafizul, et al.
Published: (2014)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Influence of electrode cooling on material migration among the electrodes during edm of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during EDM of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Dissimilar materials laser welding characteristics of stainless steel and titanium alloy
by: Mohid, Zazuli, et al.
Published: (2014)

Characterization of anisotropic damage behaviour of recycled aluminium alloys AA6061 undergoing high velocity impact
by: Ho, C.S., et al.
Published: (2019)

Enhancing mechanical and structural properties of TiC inserts using microwave energy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Influence of electrode cooling on recast layers and micro crack in EDM of titanium
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of the instability of chip formation and preheating of work on tool life in maching high temperature resistant steel and titanium alloys
by: Amin, A. K. M. Nurul, et al.
Published: (1986)

Tungsten inert gas surface alloying of commercial purity titanium (CP-Ti) with Fe-C-Si ternary mixtures
by: Adeleke, S.A., et al.
Published: (2014)

Influence of altered Ca-P based electrolytes on the anodised titanium bioactivity
by: Alipal, J., et al.
Published: (2021)

The effects of sliding parameters on dry wear characteristics of Ti-6Al-4V alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2015)

In vitro bioactivities of anodised titanium in mixtrue of B-Glycerophosphate and calcium acetate for biomedical application
by: Lee, Te Chuan
Published: (2016)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
by: Khan, Ahsan Ali, et al.
Published: (2013)

Improved tool life in end milling ti-6al-4v through workpiece preheating
by: Ginta , Turnad L., et al.
Published: (2009)

The effects of process variables on the hardness of nitrided 3% chromium steel
by: Mridha, Shahjahan, et al.
Published: (2008)

Effect of microwave sintering treatment to the flank wear of titanium carbide tools in milling operations
by: Iqbal, Mohammad, et al.
Published: (2015)

Effect Of Aluminium (Al) And Nickel (Ni) Addition On Formation Of Titanium Silicon Carbide (Ti3sic2) Via Arc Melting
by: Mazuki, Norlailatullaili
Published: (2012)

Analysis of tool wear and hole quality during Ultrasonic Assisted Drilling (UAD) of Carbon Fibre Composite (CFC)/titanium alloy (Ti6Al4V) stacks
by: Dahnel, Aishah Najiah, et al.
Published: (2015)

TIG melted surface modified titanium alloy for automotive cylinder liner application
by: Adelek, S.A., et al.
Published: (2014)

Surface features of TIG melting coated CP-titanium
by: Adeleke, S.A., et al.
Published: (2015)