Discharge, microstructural and mechanical properties of ZrO2 addition on MgO for plasma display panel materials

QR Code

Discharge, microstructural and mechanical properties of ZrO2 addition on MgO for plasma display panel materials

One of the major parts in the plasma display panel is its protecting layer. MgO thin film has been widely used as a protective layer for dielectric materials. Adding another material to the MgO base material is an alternative method for improving its property as protective layer. A study on reducin...

Full description

Bibliographic Details
Main Authors:	Bakri, Jufriadi, Sutjipto, Agus Geter Edy, Othman, Raihan, Muhida, Riza
Format:	Article
Language:	English
Published:	Maney Publishing 2009
Subjects:	TA401 Materials of engineering and construction TJ163.26 Energy conservation TK7800 Electronics. Computer engineering. Computer hardware. Photoelectronic devices
Online Access:	http://irep.iium.edu.my/2846/ http://irep.iium.edu.my/2846/1/MRI_2009.pdf

Similar Items

Microstructure and electrical properties of AZO films prepared by RF magnetron sputtering
by: Bakri, Jufriadi, et al.
Published: (2011)

Analysis of solar desalination system using heat pump
by: Amin, Zakaria Mohd., et al.
Published: (2015)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

Numerical investigation of flow boiling in double-layer microchannel heat sink
by: Ahmed, Shugata, et al.
Published: (2014)

Numerical analysis of heat transfer and nanofluid flow in a triangular duct with vortex generator: two-phase model
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

A triangular double layer microchannel heat sink: effect of parallel and counter flow
by: Manaf, Hazli, et al.
Published: (2014)

Waste heat recovery in heat pump systems: solution to reduce global warming
by: Baradey, Yehya, et al.
Published: (2015)

Active control of suddenly expanded flow
by: Khan, Sher Afghan, et al.
Published: (2000)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Seder, Islam M.F., et al.
Published: (2014)

Modelling and validation of proton exchange membrane fuel cell (PEMFC)
by: Mohiuddin, A. K. M., et al.
Published: (2018)

Performance analyses of horizontal axis wind turbines using QBlade
by: Zuhdi, Amirul Hakim, et al.
Published: (2017)

Investigation of aluminum heat sink design with thermoelectric generator
by: Mohiuddin, A. K. M., et al.
Published: (2017)

Validated analytical modeling of diesel engine regulated exhaust CO emission rate
by: Faris, Waleed Fekry, et al.
Published: (2016)

Comparative heat transfer analysis in different mini-channel heat sinks
by: Afzal, Asif, et al.
Published: (2017)

Energy harvesting from aerodynamic instabilities: Current prospect and future trends
by: Bashir, Musavir, et al.
Published: (2018)

Numerical investigation of semiempirical relations representing the local Nusselt number magnitude of a pin fin heat sink
by: Siddiqi, Mohammad Umar, et al.
Published: (2019)

On numerical investigation of semi-empirical relations representing local nusselt number at lower nozzle-target spacing’s
by: Siddique, Mohd Umair, et al.
Published: (2019)

Threaded spikes for bluff body base flow control
by: Khan, Sher Afghan, et al.
Published: (2019)

Hydrocarbons as alternative refrigerants in domestic refrigerators
by: S, Parashurama, et al.
Published: (2019)

Control of ideally expanded and under expanded nozzle flows with micro jets
by: G M, Fharukh Ahmed, et al.
Published: (2016)

Investigation on producing silica from rice husk biomass
by: Uddin, M.N., et al.
Published: (2018)

Thermo-mechanical analysis and estimation of turbine blade tip clearance of a small gas turbine engine under transient operating conditions
by: Kumar, Rahul, et al.
Published: (2020)

Magnetically plucked piezoelectric energy harvester via hybrid kinetic motion
by: Azam, Huda, et al.
Published: (2019)

A desalination system utilizing solar ambient and waste energy
by: Hawlader, M N A, et al.
Published: (2011)

Transport analysis of an Air Gap Membrane Distillation (AGMD) process
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2011)

Optimization of cooling systems in data centre by computational fluid dynamics model and simulation
by: Romadhon, Rahmat, et al.
Published: (2009)

Reconstruction and electronic properties of interface between carbon nanotubes and ferromagnetic co electrodes
by: Cuong, Nguyen Tien, et al.
Published: (2012)

Optimization of a cooling system in data centers
by: Ali, Maisarah, et al.
Published: (2012)

An active cooling system for photovoltaic module
by: Teo, H. G., et al.
Published: (2012)

Combined water and power plant (CWPP) — a novel desalination technology
by: Mahbub, Fazle, et al.
Published: (2009)

PERFORMANCE OF A SOLAR INTEGRATED HEAT PUMP AIR-CONDITIONER, WATER HEATER AND DRYER
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (2008)

Performance evaluation of a mechanical vapor compression desalination system
by: Bahar, Rubina, et al.
Published: (2004)

Economic evaluation of a solar water heating system
by: Hawlader, Mohammad Nurul Alam, et al.
Published: (1987)

Pretreatment of seawater: Results of pilot trials in Singapore
by: Chua, K T, et al.
Published: (2003)

EMK 402 - SISTEM PENUKARAN TENAGA OKT-NOV 1994.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (1994)

EMH 462(3) - ENERGY CONVERSION SYSTEM APRIL 07.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2007)

EMH 462E(3) - ENERGY CONVERSION SYSTEM APR-MEI 06.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (2006)

EMK 402 - SISTEM PENUKARAN TENAGA APRIL 1997.
by: PPKM, Pusat Pengajian Kejuruteraan Mekanikal
Published: (1997)

On the effects of tangential air inlets distribution configurations to the combustion characteristics of a direct injection liquid fueled Swirl Flameless Combustor (SFC)
by: K., Adam, et al.
Published: (2021)

Pro-environmentalists behavioural assessment towards energy conservation among Malaysian university students
by: Mohamad Kawi, Nur Farisha Husna, et al.
Published: (2021)