Manufacturing engineering education in IIUM

QR Code

Manufacturing engineering education in IIUM

This paper presents how manufacturing engineering curriculum in International Islamic University Malaysia (IIUM) is designed to prepare its graduates fit for manufacturing industry. Since the inception in 1994, IIUM has been preparing its students through specialization in manufacturing engineerin...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Amin, A. K. M. Nurul, Haque, Md. Mohafizul
Format:	Proceeding Paper
Language:	English
Published:	2007
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/27383/ http://irep.iium.edu.my/27383/1/072_RCEE_JB_2007_473-478.pdf

Similar Items

Microengineering education in IIUM: challenges and successes
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Selection of materials and manufacturing processes for green engineering
by: Haque, Md. Mohafizul, et al.
Published: (2009)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

A new approach of applying cryogenic coolant in turning AISI 304 stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

Performance of different abrasive materials during abrasive water jet machining of glass
by: Khan, Ahsan Ali, et al.
Published: (2007)

Investigation on structure and properties of brass casting
by: Haque, Md. Mohafizul, et al.
Published: (2008)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Focused Ion Beam Nanomachining of Cell Culture Sheet (softcopy not yet available)
by: Ali, Mohammad Yeakub
Published: (2011)

Manufacturing of 10 cc volumetric displacement four stroke petrol model engine cylinder block using metal casting process
by: Norazlin, Md. Kalil
Published: (2010)

Design and development of Acrylic Die for producing wax pattern to gabricate hip bone joint
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Study on the microstructure and properties of Fe-C-Si and Fe-C-Al Cast irons
by: Shaha, Sugrib Kumar, et al.
Published: (2011)

Fabricating micromilling tool using wire electrodischarge grinding and focused ion beam sputtering
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Design Evaluation Method for Design Engineer in Manufacturing Industries using Integrated Rough-Grey Analysis Approach
by: Faiz, Mohd Turan, et al.
Published: (2014)

Organizing the Internal Manufacturing Complexity Elements in Adaptation of Current Manufacturing Environment: A Fuzzy Approach
by: Mohd Noor Hanif, M. R., et al.
Published: (2022)

Awareness of sustainable manufacturing practices in Malaysian manufacturers
by: Jafartayari, Saman
Published: (2010)

Knowledge management to boost productivity in manufacturing
by: Mansor, M. A., et al.
Published: (2018)

Development of 5S practice checklist for manufacturing industry
by: Khamis, N., et al.
Published: (2009)

Metabolic energy of manual lifting in manufacturing industry
by: Iqbal, Mohammad
Published: (2011)

Process capability analysis in manufacturing titanium dioxide
by: Nurul Hidayah, Razak
Published: (2008)

Design and manufacture of a ten ton capacity wedge jack
by: Azim, M. Anwarul, et al.
Published: (1989)

Investigation of finish cut of micro electro discharge milling for nano surface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Feasibility of local manufacturer of spares for fertilizer factories of Bangladesh-a case study
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

Simulation modeling of a manufacturing process using Tecnomatix plant simulation software
by: Nurul Najihaha, ., et al.
Published: (2021)

Effect of process variables on structure and properties of aluminium–silicon piston alloy
by: Haque, Mohafizul Md, et al.
Published: (1998)

Durability and tribological properties of thermally sprayed wc cermet coating under lubricated rolling-sliding contact
by: Nuruzzaman, D. M., et al.
Published: (2007)

Geometrical integrity of micromold cavity sputtered by FIB using multilayer slicing approach
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Investigation of surface roughness in micro-electro discharge machining of nonconductive ZrO2 for MEMS application
by: Sabur, Abdus, et al.
Published: (2013)

Investigation of tribological issues in microforming: a review
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Characterisation of surface texture using AFM with trimmed probe tip
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Mechanical performance and water absorption resistance of HIPS/MWCNTs nanocomposite
by: Al-Ghamdi, Ahmed S., et al.
Published: (2012)

Surface roughness of sputtered silicon. I. surface modeling
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Surface roughness of sputtered silicon. II. Model verification
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Micro/Meso Mechanical Manufacturing (M4): opportunities and challenges: a review
by: Reyad, Mehfuz, et al.
Published: (2006)

Application of Activity-Based Costing In Electronic Manufacturing
by: Nurul Farahin, Zamrud, et al.
Published: (2019)

Sidewall surface roughness of Sputtered Silicon 1: surface modelling
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Current and future challenges of hybrid electrochemical-mechanical machining process for micro- and nano-manufacturing
by: Ahmad Shahir, Jamaludin, et al.
Published: (2024)