Fabrication of microcomponents by injection molding

QR Code

Fabrication of microcomponents by injection molding

Miniaturization has been and will continue to be the trend of research and development. A number of microfabrication processes have been developed for the realization of three-dimensional microcomponents. Among these techniques, the micromolding process is one of the key technologies for low-cost ma...

Full description

Bibliographic Details
Main Authors:	Yuan , S., Ngoi, B. K. A., Hung, N. P., Ali, Mohammad Yeakub
Format:	Proceeding Paper
Language:	English
Published:	2004
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/27183/ http://irep.iium.edu.my/27183/1/063_ICoPE_2004_Singapore_604-610.pdf

Similar Items

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Molding of three-dimensional microcomponents
by: Hung, W. N. P., et al.
Published: (2006)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Producing LIGA-competitive microcomponents
by: Hung, N. P., et al.
Published: (2000)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

3D printed mold insert infill analysis for injection molding application
by: Nur Syamimi, Mohd Salleh, et al.
Published: (2024)

Particle size and injection temperature effect on the injection molding of SS316l powder
by: Jamaludin, Khairur Rijal, et al.
Published: (2008)

Knowledge-based approach for stretch blow molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Fabrication of three dimensional micro-components – A review
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Surface roughness of FIB sputtered silicon
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Mass-replication of micro-components
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Sidewall surface roughness of Sputtered Silicon 1: surface modelling
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Warpage analysis on thick shell part using response surface methodology (RSM) and bat algorithm (BA) to optimize parameter setting in injection molding process
by: Ch'Ng, S. Q., et al.
Published: (2018)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Fabrication of Micropillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of micropillar sheet for cell culture dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Surface roughness of ion-sputtered micromold
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Fabrication of silicon nanopillar sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Fabrication of Bio-MEMS Nanostructure by focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Design and fabrication of the blow mold component
by: Mohd Azuan, Abu Shah
Published: (2007)

Numerical Simulation of Fibre Orientation in Simple Injection Molding Processes
by: Oumer, A.N., et al.
Published: (2009)

Micromolding of three-dimensional components
by: Hung, W. N. P., et al.
Published: (2001)

Simulation on effect of preform diameter in injection stretch blow molding
by: Tan, Z Q, et al.
Published: (2018)

A review of focused ion beam sputtering
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry
by: Vivekanandan, Panneerselvam, et al.
Published: (2019)

Flow behaviour to determine the defects of green part in metal injection molding
by: Mohamad Nor, Nor Hafiez, et al.
Published: (2009)

Rheological investigation of water atomized metal injection molding (MIM) feedstock for processibility prediction
by: Jamaludin, Khairur Rijal, et al.
Published: (2010)

Optimization of EDM parameters for micro/meso fabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Rheological characterization of water atomised stainless steel powder for micro metal injection molding
by: Ibrahim, Mohd. Halim Irwan, et al.
Published: (2009)

Modeling and Flow Analysis of Pure Nylon Polymer for Injection Molding Process
by: Nuruzzaman, D. M., et al.
Published: (2016)

Development of Microreplication Process - Micromolding
by: Yuan, Shu, et al.
Published: (2003)

Numerical Prediction of Flow Induced Fibers Orientation in Injection Molded Polymer Composites
by: A. N., Oumer, et al.
Published: (2015)

Optimisation of Injection Moulding Process Parameters
by: Guna Rao, Kishyen Raao, et al.
Published: (2024)

Mathematical modeling of sputtering-induced surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Nanopillar Array for Cell Culture Dish
by: Ali, Mohammad Yeakub
Published: (2011)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

Focused ion beam micromachining of mems
by: Ali, Mohammad Yeakub
Published: (2008)