Developing a prototype micro hot embossing setup

QR Code

Developing a prototype micro hot embossing setup

This paper discusses the development of a prototype of micro hot embossing setup. It included microtool, heating jig, temperature controller, cooling system, etc. The total cost was about few thousand USD. All these components were used with the help of a numerical control (NC) milling machine. The...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Ayob, Mohd Hafiz, Mohd Isa, Saiful Adzli
Format:	Proceeding Paper
Language:	English
Published:	2005
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/27181/ http://irep.iium.edu.my/27181/1/061_IMEC_2005_MS39_IEB_Dhaka_34-39.pdf

Similar Items

Polymeric micro-fluidic channel by hot embossing
by: Mohammad, Amar Sami, et al.
Published: (2006)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Hot Embossing of Micro Grating and Its Replication Accuracy
by: Muhammad Syahrir, Ahmad, et al.
Published: (2024)

Rapid Fabrication of Glass Micro and Nanostructures via Laser-assisted Hot Embossing
by: Lee, Helen May Shian, et al.
Published: (2023)

Experimental and Numerical Simulation of Hot Embossing for Fabrication of Glass Microlens Array
by: Lee, Helen May Shian, et al.
Published: (2022)

Rapid Direct Continuous Method for Hot Embossing of Glass Microlens Array Combined with CO2 Laser Irradiation and External Preheating/Cooling
by: Syarifah Nur Hasanah, Syed Kamarudin, et al.
Published: (2021)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Fabrication of glass microlens array using laser-assisted contactless hot embossing
by: Lee May Shian, Helen, et al.
Published: (2022)

Hierarchical Production Planning, Framework For The Batch Production Environment With Setup Time And Setup Cost Restrictions
by: Teo , Siew Chein
Published: (2005)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Micro-drilling of metallic materials for microsystems technology
by: Ali, Mohammad Yeakub
Published: (2008)

Geometrical integrity of microholes produced by micro-EDM
by: Ali, Mohammad Yeakub
Published: (2008)

Micro-manufacturing technology: the huge opportunity of thinking small
by: Ali, Mohammad Yeakub
Published: (2011)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Simulation of micro-injection molding
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Mass-replication of micro-components
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Evaluation of glass nano/microstructures replication fidelity after laser-assisted hot embossing process
by: Lee, May Shian Helen
Published: (2023)

Fabrication of three dimensional micro-components – A review
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Investigation of recast layer of non-conductive ceramic due to micro-EDM
by: Mohamed, Abd. Rahman, et al.
Published: (2014)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Empirical modelling of vibration in micro end milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Micro/Meso Mechanical Manufacturing (M4): opportunities and challenges: a review
by: Reyad, Mehfuz, et al.
Published: (2006)

Heuristic Optimization of Cooling Channel Design in the Hot Stamping Die for Hot Stamping Process
by: Mohd Fawzi, Zamri, et al.
Published: (2015)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Optimization of EDM parameters for micro/meso fabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Prototype development of optimum irregular milling tools for chatter supression in machining automotive product
by: Yusoff, A. R., et al.

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Effect of conventional EDM parameters on micromachined surface roughness and fabrication of hot embossing master and microtool
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Investigation of finish cut of micro electro discharge milling for nano surface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)