Wire electrical discharge machining for microfabrication

QR Code

Wire electrical discharge machining for microfabrication

This paper discusses the application of conventional wire electrical discharge machining (WEDM) for fabrication of miniaturized components using low pulse energy. The surface finish of the fabricated microparts was investigated for different level of discharge current at constant gap voltage and p...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, N.I, Rashidah, N.A, Azima
Format:	Proceeding Paper
Language:	English
Published:	2007
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/27174/ http://irep.iium.edu.my/27174/1/054_ICME_Dhaka_2007_AM-08.pdf

Similar Items

Experimental study of conventional wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Dimensional accuracy in dry micro wire electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Dry electrical discharge machining: an environmental friendly machining process
by: Ali, Mohammad Yeakub
Published: (2018)

Machine Parameter Optimization For Wire-Electric Discharge Machining
by: F. R. M., Romlay, et al.
Published: (2008)

Performance evaluation of wire electrical discharge machining on Titanium Alloy
by: Tan, Jun Qi, et al.
Published: (2018)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

A study on Wire Breakage in Electrical Discharge Machining of Polyurethane Foam
by: Azmir, Azhari, et al.
Published: (2017)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic
by: Moudood, M. A., et al.
Published: (2014)

Surface integrity of mild steel in wire electrical discharge machining
by: Mohamad Suffi, Kamari
Published: (2010)

Study Of The Surface Integrity Of AISI 4140 Steel In Wire Electrical Discharge Machining
by: Mas Ayu, Hassan, et al.
Published: (2009)

Experimental study of electrical discharge drilling of stainless steel UNS S30400
by: Hanash, Ebrahim, et al.
Published: (2018)

Wire Electrical Discharge Machining of Tungsten Carbide
by: Mas Ayu, Hassan
Published: (2008)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Current Research Trends on Dry, Near-Dry and Powder Mixed Electrical Discharge Machining
by: M. M., Noor, et al.
Published: (2011)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Optimization Of A Cutting Process For Wire-Electric Discharge Machining At Welding Joint
by: F. R. M., Romlay, et al.
Published: (2007)

Study of the Surface Integrity of AISI 4140 Steel in Wire Electrical Discharge Machining
by: Mas Ayu, Hassan, et al.
Published: (2009)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Modeling and simulation of wire electrical discharge machine process in machining aluminium alloy T6 6061
by: Yusriezal, Mamat
Published: (2008)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Wire electrical discharge machining of Ti-48Al intermetalic alloys using taguchi approach
by: Kamsir, Abdul Sukur
Published: (2006)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Application of focused ion beam for machining of nanopillar sheet
by: Ali, Mohammad Yeakub
Published: (2011)

Performance evaluation of wire electro-discharge machining on tungsten carbide
by: Hassan, Mas Ayu
Published: (2006)

Opportunities and ehallenges in Nanoparticles Formation by Electrical Discharge Machining
by: Khilji, Irshad Ahamad, et al.
Published: (2021)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Micro electro discharge machining of nonconductive ceramic: the issue of spalling
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Present and future research trend in electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)