Fabrication of micromold cavity for microreplication: A review

QR Code

Fabrication of micromold cavity for microreplication: A review

In this paper, various fabrication techniques for micromold cavity are reviewed and discussed. Silicon and lithography based fabrication were being used for years for the fabrication of micromold cavity. In the later stage direct fabrication techniques such as focused ion beam, micro electro disc...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Khan, Ahsan Ali, Mehfuz, R., Aishah, S., Hayati, N., Hajar, N.
Format:	Proceeding Paper
Language:	English
Published:	2008
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/27157/ http://irep.iium.edu.my/27157/1/048_ICME_2008_JB_MFG_ID-0127.pdf

Similar Items

Development of Microreplication Process - Micromolding
by: Yuan, Shu, et al.
Published: (2003)

Geometrical integrity of micromold cavity sputtered by FIB using multilayer slicing approach
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Development of a micromolding process
by: Hung, N. P., et al.
Published: (2001)

Micromolding of three-dimensional components
by: Hung, W. N. P., et al.
Published: (2001)

Surface roughness of ion-sputtered micromold
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Investigation of finish cut of micro electro discharge milling for nano surface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Micro/Meso Mechanical Manufacturing (M4): opportunities and challenges: a review
by: Reyad, Mehfuz, et al.
Published: (2006)

Fabrication of three dimensional micro-components – A review
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Optimization of EDM parameters for micro/meso fabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Fabrication of Micropillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Investigation of burr formation in micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Fabricating micromilling tool using wire electrodischarge grinding and focused ion beam sputtering
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Effect of cryogenic cooling during grinding of mild steel and stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2008)

Fabrication of micropillar sheet for cell culture dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of silicon nanopillar sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Fabrication of Bio-MEMS Nanostructure by focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Investigation of tribological issues in microforming: a review
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Fabrication of microcomponents by injection molding
by: Yuan , S., et al.
Published: (2004)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface roughness of sputtered silicon. I. surface modeling
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

A Review On The Fabrication Techniques Of Aluminium Matrix Nanocomposites
by: Marini, C. D., et al.
Published: (2015)

Producing LIGA-competitive microcomponents
by: Hung, N. P., et al.
Published: (2000)

Mathematical modeling of sputtering-induced surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

Focused Ion Beam Nanomachining of Cell Culture Sheet (softcopy not yet available)
by: Ali, Mohammad Yeakub
Published: (2011)

A new approach of applying cryogenic coolant in turning AISI 304 stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Application of focused ion beam micromachining: a review
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2012)

Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel
by: Afifah, Ali, et al.
Published: (2010)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)