Investigation of finish cut of micro electro discharge milling for nano surface finish

QR Code

Investigation of finish cut of micro electro discharge milling for nano surface finish

In this paper the machining condition to achieve nano surface roughness in finish cut micro electro discharge milling was investigated. The effect of feed rate and capacitance were studied on average surface roughness (Ra), and maximum peak-to-valley roughness height (Ry). Statistical models were...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Mehfuz, R.
Format:	Proceeding Paper
Language:	English
Published:	2008
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/27156/ http://irep.iium.edu.my/27156/1/047_nanoMan_2008_Spore_ID27.pdf

Similar Items

Finish cut of titanium alloy using micro electro discharge milling for nano surface finish
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of finish cut of microelectrodischarge milling for nanosurface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Influence of nano powder mixed dielectric fluid on surface finish in micro electro discharge machining of zirconia
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Investigation of TWR for finish cut of titanium alloy using Micro Electro Discharge Milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of MRR for finish cut of titanium alloy using micro electro discharge milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Micro electro discharge machining of micro pillar array: analysis of surface finish
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

High aspect ratio micro-EDM drilling with nano surface finish
by: Ali , Mohammad Yeakub, et al.
Published: (2016)

Dimensional accuracy of micro-electro discharge milling
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Investigation of surface roughness in micro-electro discharge machining of nonconductive ZrO2 for MEMS application
by: Sabur, Abdus, et al.
Published: (2013)

Powder Mixed Micro Electro Discharge Milling of Titanium Alloy: Analysis of Surface Roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Noble tool based micromilling for nanometric surface finish
by: Ali, Mohammad Yeakub
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Prediction and investigation of surface quality in high speed end-milling of silicon to eliminate conventional finishing operations
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Surface finish prediction models for precision grinding of silicon
by: Alao, Abdur-Rasheed, et al.
Published: (2011)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Investigation on the surface finish, MRR and the surface damage during the EDM of tungsten carbide
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Micro electro discharge machining of nonconductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Micro electro discharge machining of non-conductive ceramic
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Investigation of vibration and surface roughness in micro milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

ELID grinding and EDM for finish machining
by: Saleh, Tanveer, et al.
Published: (2017)

Magnetorheological finishing on metal surface: a review
by: N. A., Mutalib, et al.
Published: (2019)

Experimental investigation on magnetorheological finishing process parameters
by: Abdul Wahab, Hashmi, et al.
Published: (2022)

Micro electro discharge machining of nonconductive ceramic: the issue of spalling
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

Electro-discharge machining of alumina: investigation of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Cutting Tools in Finishing Operations for CNC Rapid Manufacturing Processes: Simulation Studies
by: M. Nafis, O. Z., et al.
Published: (2014)

Investigation of burr formation in micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Surface study when finish grinding silicon using resin bonded diamond cup wheel
by: Konneh, Mohamed, et al.
Published: (2011)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: analysis of surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2012)