Investigation of burr formation in micro end milling

QR Code

Investigation of burr formation in micro end milling

This paper discussed the investigation of the burr formation in micro end milling process on stainless steel. Thus, formation of burr after machined by micro end milling process was investigated and analyzed. Tungsten carbide end mill cutting tool of diameter 500 μm was used with depth of cut of 2...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Alif, M., Irman, K., Hajar, N., Hayati, N.
Format:	Proceeding Paper
Language:	English
Published:	2008
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/27155/ http://irep.iium.edu.my/27155/1/046_ICSTiE_2008__UiTM_Penang_714-718.pdf

Similar Items

Prediction of burr formation in fabricating MEMS components by micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Prediction of burr formation in fabricating MEMS components by micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Elimination of burr formation during end milling of Polymethyl Methacrylate (PMMA) through high speed machining
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Investigation of burr in high speed microdrilling
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Effect of micro-milling parameters on burr formation and surface roughness in aluminum microchannels puncher
by: Mohd Saifuldin, Mohd Mokhtar, et al.
Published: (2024)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Investigation of vibration and surface roughness in micro milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Investigation of finish cut of micro electro discharge milling for nano surface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Empirical modelling of vibration in micro end milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Using Finite Element simulation to investigate the effect of cutting edge radius on burr formation for inclined dimple milling operation
by: Mohd Ali Hanafiah, Shaharudin, et al.
Published: (2023)

Study on end brush deburring and sintered diamond ball deburring of micro-features milled
by: Sai, T. K., et al.
Published: (2019)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Role of chip serration frequency in chatter formation during end milling operation of stainless steel
by: Anayet Ullah Patwari, Mohammed, et al.
Published: (2010)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Fabrication of micro dimples pattern using ball end mill
by: Muhamad Izdhar, Zaki, et al.
Published: (2019)

Dimensional accuracy of micro-electro discharge milling
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Powder mixed micro electro discharge milling of titanium alloy: Investigation of material removal rate
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Prediction and investigation of surface quality in high speed end-milling of silicon to eliminate conventional finishing operations
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

A new technique for the investigation of chatter formation during end milling of medium carbon steel (AISI 45)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Micro end milling of AISI 304 stainless steel and analysis of micro surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

High speed end milling of single crystal silicon wafer
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Effect of machining parameters on micro-burrs formation of aluminium puncher using high-speed machining process
by: Mohd Saifuldin, Mokhtar, et al.
Published: (2024)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
by: Ali, Mohammad Yeakub
Published: (2009)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Investigation of surface roughness in micro-electro discharge machining of nonconductive ZrO2 for MEMS application
by: Sabur, Abdus, et al.
Published: (2013)

Multi-criteria optimization in end milling of AISI D2 hardened steel using coated carbide inserts
by: Karim, A.N. Mustafizul, et al.
Published: (2011)

Chip pattern, burr and surface roughness in laser assisted micro milling of Ti6Al4V using micro ball end mill
by: Mohid, Z., et al.
Published: (2018)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Chip serration frequency-the primary cause of chatter during end milling operation
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)

Vibration issue in micro end milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Performance of uncoated WC-Co in end milling of Aluminium Silicon Carbide (AlSiC)
by: M. K. , Nor Khairusshima, et al.
Published: (2011)

Identification of instabilities of the chip formation and it's prediction model during end milling of medium carbon steel (S45C)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)