Development of a micromolding process
This paper presents the simulating and experimental results of a micromolding process for fabrication of threedimensional (3D) microcomponents. The maskless process utilizes a micro electrical discharging system for bulk machining, then finish machining using focused-ion beam to sputter the mold m...
| Main Authors: | , , , |
|---|---|
| Format: | Proceeding Paper |
| Language: | English |
| Published: |
2001
|
| Subjects: | |
| Online Access: | http://irep.iium.edu.my/27139/ http://irep.iium.edu.my/27139/1/035_DTIP-SPIE_France_2001_317-328_Hung.pdf |
| _version_ | 1848779767078191104 |
|---|---|
| author | Hung, N. P. Yuan, S. Lee, E. C. W. Ali, Mohammad Yeakub |
| author_facet | Hung, N. P. Yuan, S. Lee, E. C. W. Ali, Mohammad Yeakub |
| author_sort | Hung, N. P. |
| building | IIUM Repository |
| collection | Online Access |
| description | This paper presents the simulating and experimental results of a micromolding process for fabrication of threedimensional
(3D) microcomponents. The maskless process utilizes a micro electrical discharging system for
bulk machining, then finish machining using focused-ion beam to sputter the mold microcavity, which is then
filled with various types of plastics. Simulation using commercially available software reveals possible
problems in micromolding, and the simulation results of microgears (φ100-1000μm diameter, 1:1 aspect ratio)
are compared with those from actually molded microgears.
Although the software prohibits modeling of a stand-alone microgear with diameter below φ1000μm when
using a 2.5D model and φ220μm for a 3D model, the simulation succeeds upon integrating a microgear of
φ100μm with a larger base. Selecting the polymers from the built-in data bank, the simulation pinpoints
locations for trapped gas, predicts filling time, volumetric shrinkage, uniformity, and distribution of pressure,
shear rate, stress.... It correctly predicts underfilling of the cavity when the mold temperature is below a
threshold, but fails to locate the weld lines. Minimum channel sizes for proper flow of several plastics are
presented, and the mold temperature must be controlled for proper flow of polymer into a microcavity. The
measured viscosity of tested polymers compliments the experimental and simulating results. |
| first_indexed | 2025-11-14T15:23:00Z |
| format | Proceeding Paper |
| id | iium-27139 |
| institution | International Islamic University Malaysia |
| institution_category | Local University |
| language | English |
| last_indexed | 2025-11-14T15:23:00Z |
| publishDate | 2001 |
| recordtype | eprints |
| repository_type | Digital Repository |
| spelling | iium-271392013-09-06T07:42:45Z http://irep.iium.edu.my/27139/ Development of a micromolding process Hung, N. P. Yuan, S. Lee, E. C. W. Ali, Mohammad Yeakub TS Manufactures This paper presents the simulating and experimental results of a micromolding process for fabrication of threedimensional (3D) microcomponents. The maskless process utilizes a micro electrical discharging system for bulk machining, then finish machining using focused-ion beam to sputter the mold microcavity, which is then filled with various types of plastics. Simulation using commercially available software reveals possible problems in micromolding, and the simulation results of microgears (φ100-1000μm diameter, 1:1 aspect ratio) are compared with those from actually molded microgears. Although the software prohibits modeling of a stand-alone microgear with diameter below φ1000μm when using a 2.5D model and φ220μm for a 3D model, the simulation succeeds upon integrating a microgear of φ100μm with a larger base. Selecting the polymers from the built-in data bank, the simulation pinpoints locations for trapped gas, predicts filling time, volumetric shrinkage, uniformity, and distribution of pressure, shear rate, stress.... It correctly predicts underfilling of the cavity when the mold temperature is below a threshold, but fails to locate the weld lines. Minimum channel sizes for proper flow of several plastics are presented, and the mold temperature must be controlled for proper flow of polymer into a microcavity. The measured viscosity of tested polymers compliments the experimental and simulating results. 2001 Proceeding Paper PeerReviewed application/pdf en http://irep.iium.edu.my/27139/1/035_DTIP-SPIE_France_2001_317-328_Hung.pdf Hung, N. P. and Yuan, S. and Lee, E. C. W. and Ali, Mohammad Yeakub (2001) Development of a micromolding process. In: International Symposium on Design, Test, Integration and Packaging of MEMS/MOEMS 2001, 25-27 April 2001, Cannes, France. |
| spellingShingle | TS Manufactures Hung, N. P. Yuan, S. Lee, E. C. W. Ali, Mohammad Yeakub Development of a micromolding process |
| title | Development of a micromolding process |
| title_full | Development of a micromolding process |
| title_fullStr | Development of a micromolding process |
| title_full_unstemmed | Development of a micromolding process |
| title_short | Development of a micromolding process |
| title_sort | development of a micromolding process |
| topic | TS Manufactures |
| url | http://irep.iium.edu.my/27139/ http://irep.iium.edu.my/27139/1/035_DTIP-SPIE_France_2001_317-328_Hung.pdf |