Fabricating micromilling tool using wire electrodischarge
grinding and focused ion beam sputtering

QR Code

Fabricating micromilling tool using wire electrodischarge grinding and focused ion beam sputtering

This paper discusses the microfabrication of micromilling tools using wire electrodischarge grinding (WEDG) and focused ion beam (FIB) sputtering. The tool blank of tungsten carbide was produced by WEDG and the cutting edges were formed by FIB sputtering. Using these two complementary processes...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Ong, A. S.
Format:	Article
Language:	English
Published:	Springer 2006
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/27106/ http://irep.iium.edu.my/27106/1/018_IJAMT_31%285-6%29_501-508.pdf

Similar Items

Micromilling of tungsten carbide using focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Surface integrity and removal rate of silicon sputtered with focused ion beam
by: Hung, NguyenPhu, et al.
Published: (2001)

A review of focused ion beam sputtering
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Parametric study of sputtering microchannels via focused ion beam (FIB)
by: Mohd Shahar, Siti Fatimah, et al.
Published: (2015)

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Fabrication of Bio-MEMS Nanostructure by focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Focused ion beam machining of silicon
by: Hung, NguyenPhu, et al.
Published: (2002)

Noble tool based micromilling for nanometric surface finish
by: Ali, Mohammad Yeakub
Published: (2011)

Focused ion beam micromachining of mems
by: Ali, Mohammad Yeakub
Published: (2008)

Application of focused ion beam micromachining: a review
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2012)

Focused Ion Beam Nanomachining of Cell Culture Sheet (softcopy not yet available)
by: Ali, Mohammad Yeakub
Published: (2011)

Application of focused ion beam for machining of nanopillar sheet
by: Ali, Mohammad Yeakub
Published: (2011)

Investigation of vibration in micromilling with MQL: S/N ratio analysis
by: Hussin, Muhammad Shaffiq, et al.
Published: (2020)

Minimum chip thickness in machining MEMS structure using Tool Based Micromilling
by: Ali, Mohammad Yeakub, et al.
Published: (2011)

Investigation of microholes produced by focused ion beam micromachining
by: Mohd Fuad, Nurul Hajar, et al.
Published: (2011)

Investigation of Microholes Produced by Focused Ion Beam Micromachining
by: Mohd. Fuad, Nurul Hajar, et al.
Published: (2010)

Focused ion beam machining of cell culture dish
by: Ali, Mohammad Yeakub
Published: (2008)

Tool Wear Observation During Unconventional Low Speed Machining Using Low Cost Micromilling
by: Ainur Munira, Rosli, et al.
Published: (2021)

Surface roughness of ion-sputtered micromold
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Recent Study on Hard to Machine Material – Micromilling process
by: Ainur Munira, Rosli, et al.
Published: (2021)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Mathematical modeling of sputtering-induced surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Surface roughness of sputtered silicon. I. surface modeling
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Surface roughness of sputtered silicon. II. Model verification
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Geometrical integrity of micromold cavity sputtered by FIB using multilayer slicing approach
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Sidewall surface roughness of Sputtered Silicon 1: surface modelling
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Effect of cryogenic cooling during grinding of mild steel and stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2008)

Kerf in micro wire electro discharge machining
by: Sabur, Abdus, et al.
Published: (2011)

Sputtering of paraboloid microstructure using fib
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Surface roughness of FIB sputtered silicon
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Study on the behavior of micromilling process with the validation of finite element method
by: Nurul Hasya, Md Kamil
Published: (2025)

Precision surface grinding of silicon carbide
by: Konneh, Mohamed
Published: (2016)

ELID grinding and EDM for finish machining
by: Saleh, Tanveer, et al.
Published: (2017)

Micromilling performance analysis – cold air assisted aluminium machining behaviour observation
by: Nurul Hasya, .Md Kamil, et al.
Published: (2022)

Spectroscopic Studies of Magnetron Sputtering Plasma Discharge in Cu/O2/Ar Mixture for Copper Oxide Thin Film Fabrication
by: Ahmad Faizal, Mohd Zain, et al.
Published: (2015)

Surface finish prediction models for precision grinding of silicon
by: Alao, Abdur-Rasheed, et al.
Published: (2011)

An investigation on morphology of hard-brittle silicon surface by diamond grinding
by: Konneh, Mohamed, et al.
Published: (2006)

Design and fabricate walkingaided tool for paralyzed people
by: Abdul Rashid, Muhammad
Published: (2008)

Design and fabricate storage cabinet for turret punch tool
by: Muhammad Afiq, Ahmad Mustaza
Published: (2008)

Modelling for fabrication of microelectrodes by localized electrochemical deposition for micro-electrodischarge machining
by: Habib, Md Ahsan, et al.
Published: (2010)