Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon

QR Code

Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon

Machining of silicon is an expensive affair because its inherent brittleness leads to subsurface crack generation. Research endeavours have therefore focused on ductile mode machining of silicon to obtain crack free machined surfaces with roughness as low as 0.22 μm or even below, hence eliminati...

Full description

Bibliographic Details
Main Authors:	Amin, A. K. M. Nurul, Khalid, Noor Syairah, Mohd Nasir, Siti Nurshahida, Arif, Muammer Din
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2012
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/26306/ http://irep.iium.edu.my/26306/1/AMR.576.11.pdf

Similar Items

Statistical approach to modeling & optimization of surface roughness in high speed end milling of silicon with diamond coated tools
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Surface roughness model for high speed end milling of soda lime glass using carbide coated tools with compressed air blowing
by: Mahmud, M. A., et al.
Published: (2012)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

Application of permanent magnets for chatter control in end milling of titanium alloy Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Influence of magnetic field on reduction chatter and of surface roughness in end milling of Titanium Alloy - Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Optimization of surface roughness in end milling of titanium alloy TI-6AL-4V under the influence of magnetic field from permanents magnets
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Modeling and optimization of surface roughness and vibration amplitude in heat assisted end milling of SKD 11 tool steel using ball nose tool
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Surface roughness optimization in end milling of stainless steel AISI 304 with uncoated WC-Co insert under magnetic field
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

A study of parameters relationship to backcutting phenomena during high speed end milling of AISI H13
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Effectiveness of uncoated WC-Co and PCD inserts in end milling of aluminum silicon carbide (AlSiC)
by: M. K., Nor Khairusshima, et al.
Published: (2007)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Flank wear analysing of high speed end milling for hardened steel D2 using Taguchi method
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

High speed end milling of silicon using diamond coated tools with air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

High speed end milling of silicon using diamond coated tools with air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Influence of chatter of VMC arising during end milling operation and cutting conditions on quality of machined surface
by: A.K.M, N. Amin, et al.
Published: (2001)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Effect of cutting parameters on surface roughness in end milling of AlSi/AlN metal matrix composite
by: Tomadi, Siti Haryani, et al.
Published: (2017)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Surface integrity in end milling titanium alloy Ti6Al4V under heat assisted machining
by: Ginta, Turnad Lenggo, et al.
Published: (2013)

The effect of preheating of work on chatter during end milling of medium carbon steel performed on a Vertical Machining Center (VMC)
by: Amin, A. K. M. Nurul, et al.
Published: (2003)

Improved tool life in end milling ti-6al-4v through workpiece preheating
by: Ginta , Turnad L., et al.
Published: (2009)

Cutting temperature and surface roughness optimization in CNC end milling using multi objective genetic algorithm
by: Al Hazza, Muataz, et al.
Published: (2012)

Identification of instabilities of the chip formation and it's prediction model during end milling of medium carbon steel (S45C)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

Development of mathematical model for chip serration frequency in turning of stainless steel 304 using RSM
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

A new experimental approach to determination of critical depth in high speed machining of soda-lime glass
by: Mahmud, M.A, et al.
Published: (2012)

Implementation of magnetic damping to reduce chatter amplitude and tool wear during turning of stainless steel AISI 304
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)