Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel

QR Code

Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel

In the area of grit blasting, it is well known that microscopically small abrasive debris gets trapped on the surface, and due to impact the grits might cause the surface to fracture and a fraction of it to be embedded. The same problem appears in abrasive water jet (AWJ) machining especially in the...

Full description

Bibliographic Details
Main Authors:	Afifah, Ali, Khan, Ahsan Ali, Ali, Mohammad Yeakub
Other Authors:	Adesta, Erry Yulian Triblas
Format:	Proceeding Paper
Language:	English
Published:	Trans Tech Publications, Switzerland 2010
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/2521/ http://irep.iium.edu.my/2521/1/RMC_Book_Chapter_WAJM.pdf

Similar Items

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

Performance of different abrasive materials during abrasive water jet machining of glass
by: Khan, Ahsan Ali, et al.
Published: (2007)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)

A study on abrasive water jet machining of aluminum with garnet abrasives
by: Khan, Ahsan Ali, et al.
Published: (2005)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

A Review on Nozzle Wear in Abrasive Water Jet Machining Application
by: Syazwani, H., et al.
Published: (2016)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari, Azmir, et al.

Analysis of wear on abrasive water jet nozzle
by: Izzudin, Nazar
Published: (2016)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface roughness of carbides produced by water abrasive jet machining
by: Ali Khan, Ahsan, et al.
Published: (2011)

Effect of cryogenic cooling during grinding of mild steel and stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2008)

Investigation of the wear progression of nozzle in abrasive waterjet machining with different abrasive material
by: Lusi, Nuraini, et al.
Published: (2025)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

A study of abrasive water jet machining process on glass/epoxy composite laminate
by: M. A., Amir, et al.
Published: (2009)

Performance analysis of abrasive waterjet machining process at low pressure
by: M., Murugan, et al.
Published: (2018)

Analysis of acoustic emission during abrasive waterjet machining of sheet metals
by: Nazrin, Mokhtar, et al.
Published: (2018)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Assembly meshing of abrasive waterjet nozzle erosion simulation
by: Naqib Hakim, Kamarudin, et al.
Published: (2017)

Investigation on the effect of abrasive waterjet parameter on machining stainless steel
by: Hafiz, Husin, et al.
Published: (2020)

Computational fluid dynamic simulation of abrasive waterjet nozzle erosion
by: Naqib Hakim, Kamarudin
Published: (2020)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effect of masked abrasive waterjet texturing on surface roughness using Taguchi method
by: Hafiz, Husin, et al.
Published: (2022)

Effect of abrasive tools on surface finishing when grinding mild steel
by: Abd Faiz, Muhammad
Published: (2010)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Surface integrity of Mg-based nanocomposite produced by Abrasive Water Jet Machining (AWJM)
by: Mardi, K., et al.
Published: (2017)

Abrasive water-jet: controlled depth milling of titanium alloys
by: Fowler, Gary
Published: (2003)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Gouging abrasion test for rock abrasiveness testing
by: Golovanevskiy, Vladimir, et al.
Published: (2008)

Effect of aluminium oxide and silicon carbide abrasive type on mild steel surface temperature
by: Mohd Hizam, Mohd Noor
Published: (2010)

Influence of current, spark on-time and off-time on electrode wear during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Design and fabrication of a new replaceable nozzle for abrasive water jet application
by: Nuraini, Lusi, et al.
Published: (2025)

Effect Of Surface Topography Of 8090 Al-Li Alloy During Abrasive Waterjet Peening Process
by: Qutaba, Syed, et al.
Published: (2024)

Prediction of abrasive waterjet machining of sheet metals using artiﬁcial neural network
by: Nur Khadijah, Mazlan, et al.
Published: (2022)

Prediction of abrasive waterjet machining of sheet metals using artificial neural network
by: Nur Khadijah, Mazlan, et al.
Published: (2022)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Features of EDM of mild steel with Ta-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)