Buckling of composite perforated plates

QR Code

Buckling of composite perforated plates

The buckling behaviour of homogeneous and composite plates with cutouts under axial compression is investigated numerically by using ANSYS software. The influence of material orientation and the length to width ratio on the buckling response of the plates is examined.

Bibliographic Details
Main Authors:	Syed Mohamed Ali, Jaffar, Wan Abdullah, Wan Najihah, Aminuddin, Alina
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TA630 Structural engineering (General)
Online Access:	http://irep.iium.edu.my/24899/ http://irep.iium.edu.my/24899/1/20253.pdf

Similar Items

Effect of boundary conditions on the buckling behavior of perforated plates
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Effect of cutout shape on the critical buckling load of a perforated plate
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Buckling of long column
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Buckling of composite columns
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Buckling of thin walled sections
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Lateral crushing of composite fuselages
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Optimization of a mechanical test on composite plates with the virtual fields method
by: Syed Muhammad, Kashif, et al.
Published: (2009)

Characterization of composite plates using the virtual fields method with optimized loading conditions
by: Kashif, Syed Muhammad, et al.
Published: (2008)

Three-dimensional static shape control analysis of composite plates using distributed piezoelectric actuators
by: Shaik Dawood, Mohd. Sultan Ibrahim, et al.
Published: (2008)

Effect of bonded composite patch on the stress intensity factor for a center cracked plate
by: Aabid, Abdul, et al.
Published: (2019)

Fatigue damage characterization of aluminum alloy plates
by: Hrairi, Meftah, et al.
Published: (2011)

Propeller blade stress analysis using CATIA
by: Syed Mohamed Ali, Jaffar, et al.
Published: (2011)

Characterization of composite materials using full field data
by: Syed Muhammad, Kashif
Published: (2011)

Study of the effect of different curing setups on mechanical properties of low cost composite structures
by: Syed Muhammad, Kashif, et al.
Published: (2013)

Delamination control in composite beams using piezoelectric actuators
by: Iannucci, L, et al.
Published: (2009)

Influence of shear direction on the buckling of CFRP composite perforated plate
by: Yidris, Noorfaizal, et al.
Published: (2022)

Effect of thread material and stitch orientation on tensile mechanical property of stitched oil palm empty fruit bunch fiber reinforced epoxy composites
by: Ahamd Ghazilan, Ahmad Luqman, et al.
Published: (2016)

The constitutive equation gap method
by: Syed Muhammad, Kashif
Published: (2011)

The equilibrium gap method
by: Syed Muhammad, Kashif
Published: (2011)

The reciprocity gap method
by: Syed Muhammad, Kashif
Published: (2011)

The virtual fields method
by: Syed Muhammad, Kashif
Published: (2011)

Numerical construction of piecewise virtual fields
by: Syed Muhammad, Kashif
Published: (2011)

Numerical model of noise effect in full field data
by: Syed Muhammad, Kashif
Published: (2011)

Optimized virtual fields with noise minimization
by: Syed Muhammad, Kashif
Published: (2011)

Finite element model updating
by: Syed Muhammad, Kashif
Published: (2011)

Optimization of milling carbon fibre reinforced plastic using RSM
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Study on tool wear during milling CFRP under dry and chilled air machining
by: Muhamad Khairussaleh, Nor Khairusshima, et al.
Published: (2017)

Textile fine grined mortar containing palm oil fuel ash as a partial cement replacement for flexural strengthening on reinforced concrete beams
by: Wan Yusof, Wan Yuslinda
Published: (2018)

Mode I delamination simulation using LS-DYNA
by: Ibrahim, Mohamed S., et al.
Published: (2011)

Effect of fatigue loading on bonding shear strength at the interface between two layers concrete
by: Ali, Maisarah, et al.
Published: (1999)

Influential factors and structural reliability
by: Eusuf, Muhammad Abu, et al.
Published: (2013)

Shear wall construction in buildings: a conceptual framework on the aspect of analysis and design
by: Eusuf, Muhammad Abu, et al.
Published: (2013)

Structural behaviour of precast lightweight foamed concrete sandwich panel (PLFP) with shear truss connectors
by: Goh, Wan Inn
Published: (2015)

A concept of shear wall for the design of high-rise buildings construction
by: Abu Eusuf, Muhammad
Published: (2011)

Experimental geometric stiffness matrix formulation of beam finite element.
by: Sulaeman, Erwin
Published: (2011)

A new higher order theory for analysis of orthotropic cylindrical shell under electromechanical load
by: Adedi, Muhammad Rahman, et al.
Published: (2019)

Numerical simulations of bulk metal forming process with smooth particle hydrodynamics
by: Topa, Ameen, et al.
Published: (2014)

Dynamic characterization of vehicle structural panels
by: Hanouf, Zahir, et al.
Published: (2015)

Proposal of a probabilistic reproduction for multi- dimensional assessment of structural behavior and understanding professional ethics: a green technology approach
by: Eusuf, Muhammad Abu, et al.
Published: (2013)

Active control of high-frequency vibration: optimisation using the hybrid modelling method
by: Abdul Muthalif, Asan Gani, et al.
Published: (2012)