Enhancement of machinability of nickel based alloy - inconel 718 by
induction preheating in end milling using ceramic inserts

QR Code

Enhancement of machinability of nickel based alloy - inconel 718 by induction preheating in end milling using ceramic inserts

Unique combinations of high strength properties maintained at elevated temperature and high resistance to chemical degradation have made Nickel based alloy, Inconel 718 suitable for application as aerospace components. However, the same properties are responsible for very poor machinability of the...

Full description

Bibliographic Details
Main Authors:	Mokhtar, Suhaily, Amin, A. K. M. Nurul, Patwari, Anayet Ullah, A. Azhar, A. Hazim, A. R., Zulkhari
Format:	Proceeding Paper
Language:	English
Published:	2010
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/23312/ http://irep.iium.edu.my/23312/1/p129.pdf

Similar Items

Comparison of machinability of ceramic insert in room temperature and cryogenic cooling conditions during end milling inconel 718
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Investigation of the machinability of Inconel 718 in room temperature and preheated conditions
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Wear mechanism in end milling of Inconel 718
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Enhancement of machinability of Inconel 718 in end milling through online induction heating of workpiece
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Artificial neural network algorithm for predicting the surface roughness in end milling of Inconel 718 alloy
by: Hossain, Mohammad Ishtiyaq, et al.
Published: (2011)

Development of an artificial neural network algorithm for predicting the surface roughness in end milling of inconel 718 alloy
by: Hossain, Mohammad Ishtiyaq, et al.
Published: (2008)

Development of an artificial neural network algorithm for predicting the cutting force in end milling of Inconel 718 alloy
by: Hossain, Ishtiaq, et al.
Published: (2011)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

Prediction of surface roughness in high speed machining of Inconel 718
by: Suhaily, Mokhtar, et al.
Published: (2011)

Mathematical model of chip serration frequency in end milling of Inconel 718
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Performance of Silicon carbide whisker reinforced ceramic inserts on Inconel 718 in end milling process
by: Moola, Mohan, et al.
Published: (2016)

Application of response surface methodology coupled with genetic algorithm in the optimization of cutting conditions for surface roughness in end milling of Inconel 718 using coated WC-Co inserts
by: Ishtiyaq, M. H., et al.
Published: (2011)

A coupled artificial neural network and RSM model for the prediction of chip serration frequency in end milling of Inconel 718
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2011)

Application of response surface methodology coupled with genetic algorithm in the optimization of cutting conditions for surface roughness in end-milling of Inconel 718 using coated WC-co inserts
by: Ishtiyaq, M. H., et al.
Published: (2007)

Numerical analysis of laser preheating for laser assisted micro milling of Inconel 718
by: Abdul Rahim, Erween, et al.
Published: (2014)

Improvements in the development of silicon nitride inserts using hybrid microwave energy for machining Inconel 718
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

Machinability improvement by workpiece preheating during end milling AISI H13 hardened steel
by: Mokhtar, Suhaily, et al.
Published: (2011)

Effect of machining parameters on surface finish of Inconel 718 in end milling
by: Sarkar, B., et al.
Published: (2017)

Induction heat assisted end milling of Inconel 718 and Ti6AI4V alloys: a comparative assessment of Machinability in terms of chatter, surface roughness and tool performance
by: Amin, A. K. M. Nurul, et al.
Published: (2013)

Electrolyte jet machining for surface texturing of Inconel 718
by: Mitchell-Smith, Jonathon, et al.
Published: (2014)

Enhancement of machinability by workpiece preheating in end milling of Ti-6Al-4V
by: Hossain, Muhammad Ishtiyaq, et al.
Published: (2008)

Preheated machining in end milling of hardened steel AISI D2
by: Lajis, M. A., et al.
Published: (2008)

Enhancement of surface integrity in cryogenic high speed ball nose end milling process of inconel 718
by: Musfirah, Abdul Hadi, et al.
Published: (2020)

Preheating in end milling of AISI D2 hardened steel with coated carbide inserts
by: Lajis , M.A., et al.
Published: (2010)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Enhancing tool life with the development of silicon nitride based inserts for high speed machining of Inconel 718 using hybrid microwave sintering
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Performance of Variable Helix and Pitch Cutting Tools on Chatter Vibration in End Milling of Inconel 718
by: Hou, Hoe Chen
Published: (2018)

Life assessment of welded INCONEL 718 at high temperature
by: Tanner, David W. J.
Published: (2009)

Cutting performance and wear characteristics of PVD coated and uncoated carbide tools in face milling Inconel 718 aerospace alloy
by: Jawaid, A., et al.
Published: (2001)

Creep behaviour of inconel 718 processed by laser powder bed fusion
by: Xu, Zhengkai, et al.
Published: (2018)

Enhancing tool life of hot isostatically pressed silicon nitride inserts in machining inconel 718 with different susceptors through hybrid microwave post sintering
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

The performance of uncoated tungsten carbide insert in end milling titanium alloy Ti-6Al 4V through work piece preheating
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

The influence of coolant on tool deterioration of uncoated carbide tools in endmilling hardened inconel 718plus nickel based superalloy
by: Nurul Hidayah, Razak
Published: (2020)

Surface integrity of Inconel 718 under cryogenic and dry cutting conditions
by: Muammar Faiq Azhar,, et al.
Published: (2024)

Solvent debinding of Inconel 718 fabricated via Metal Injection Molding
by: Suleiman @ Ahmad, Muhammad Jabir, et al.
Published: (2016)

Wear behavior of PVD and CVD coated carbide tools when face milling Inconel 718
by: Jawaid, A., et al.
Published: (2000)

An experimental and numerical investigation on the process efficiency of the focused TIG welding of Inconel 718 thick plates
by: Salerno, Gervasio, et al.
Published: (2018)

Assessment of performance of uncoated and coated carbide inserts in end milling of Ti-6Al-4V through modelling
by: Hossain, Ishtiaq, et al.
Published: (2011)