Design of differential resistive measuring system and its applications

QR Code

Design of differential resistive measuring system and its applications

Differential resistive systems are easily designed using potentiometric sensors. They usually contain two sensing resistances and a common movable terminal. This circuit can be used to sense a number of scenario; such as the liquid level in a tank, biomedical applications in determining the expansi...

Full description

Bibliographic Details
Main Authors:	Abdul Wahab, Deji, Khan, Sheroz, Chebil, Jalel
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TK7800 Electronics. Computer engineering. Computer hardware. Photoelectronic devices
Online Access:	http://irep.iium.edu.my/21645/ http://irep.iium.edu.my/21645/1/DESIGN_OF_DIFFERENTIAL_RESISTIVE_MEASURING_SYSTEM_AND_ITS_APPLICATIONS.pdf

Similar Items

Wavelet analysis of the ECG signals for three common heart diseases in Jordan
by: Chebil, Jalel, et al.
Published: (2011)

The principle of resistive sensing
by: Arshad, Atika, et al.
Published: (2011)

Capacitive sensing for non-contact means of measurement
by: Tasnim, Rumana, et al.
Published: (2011)

On the electrode arrangements of capacitive sensor for two phase Gas flow measurement
by: Tasnim, Rumana, et al.
Published: (2011)

Design and dimensional analysis of interdigital sensor for blood glucose measurement through non-invasive method
by: Zaharudin, Zarimin, et al.
Published: (2020)

Convolutional neural network-based finger vein recognition using near infrared images
by: Fairuz, Subha, et al.
Published: (2018)

Comparison of empirical propagation path loss models for mobile communications in the suburban area of Kuala Lumpur
by: Chebil, Jalel, et al.
Published: (2011)

Contact type and noncontact type gas flow measuring sensors
by: Tasnim, Rumana, et al.
Published: (2011)

Sensors in electronic applications
by: Tasnim, Rumana, et al.
Published: (2011)

Signature recognition using artificial neural network
by: Abushariah, Ahmad A. M., et al.
Published: (2011)

Design an ultra-wideband modified wilkinson power divider fed-by balanced antipodal vivaldi antenna array for imaging applications
by: Shaikh, Faraz Ahmed, et al.
Published: (2020)

Design and optimization of ultra-wideband antipodal vivaldi antenna for radar and microwave imaging application
by: Shaikh, Faraz Ahmed, et al.
Published: (2018)

Design and simulation of 10 MHz MEMS oscillator
by: Taufik, Mohamad Syamsi, et al.
Published: (2014)

Application and case studies of magnetic induction
by: Arshad, Atika, et al.
Published: (2011)

Magnetic hysteresis theory :application perspective
by: Arshad, Atika, et al.
Published: (2011)

Design of two-stage CMOS amplifier for quartz crystal resonator
by: Mohd Taufik, Muhammad Syamsi, et al.
Published: (2013)

Design and simulation of Clamped-Clamped and Clamped-Free resonators
by: Zainuddin, Ahmad Anwar, et al.
Published: (2013)

Design and simulation of 20MHz oscillator using CMOS-MEMS beam resonators
by: Zainuddin, Ahmad Anwar, et al.
Published: (2013)

Design and hardware implementation of conditioning circuit for accurate reading from transducers with nonlinear responses
by: Hasan, Khairul, et al.
Published: (2011)

Acquisition of a very low voltage and a low frequency biomedical signal- frequency selective filter design
by: Shobaki, Mohammed M., et al.
Published: (2014)

Optimized RC timing technique for accurate measurement of minute capacitance changes
by: Zaharudin, Zarimin, et al.
Published: (2018)

Design and implementation of portable outdoor air quality measurement systemn using Arduino
by: Gunawan, Teddy Surya, et al.
Published: (2018)

Review of SCADA systems and IoT honeypots
by: Alquwatli, Mohammed H., et al.
Published: (2020)

Performance improvement of sensors response using piece-wise non-linear (PWL) A/D and pulse-width modulation (PWM) A/D techniques
by: Tijani, Ismaila, et al.
Published: (2011)

Power supply interference in smart sensor microcontroller interface
by: Tijani, Ismaila, et al.
Published: (2011)

Design and implementation of an optimal fuzzy logic controller using egentic algorithm
by: Abdulazeez, Salami Femi, et al.
Published: (2011)

High quality acquisition of surface electromyography – conditioning circuit design
by: Shobaki, Mohammed M., et al.
Published: (2013)

An evaluation of transform domain watermarking and its application to intellectual properties images
by: Olanrewaju, Rashidah Funke, et al.
Published: (2011)

Application of UWB wireless MIMO connectivity inside modern aircraft
by: Al-Khateeb, Khalid A. Saeed, et al.
Published: (2016)

High gain UWB horn antenna for concealed metal detection and microwave imaging application
by: Shaikh, Faraz Ahmed, et al.
Published: (2017)

Practical applications and design challenges of wireless heterogeneous sensor networks
by: Salami, Abdulazeez F., et al.
Published: (2011)

Inductive power system for energy harvesting
by: Arshad, Atika, et al.
Published: (2011)

Piece-wise linear analog to digital (PLADC) converter process
by: Salami, Abdulazeez F., et al.
Published: (2011)

Frequency reliant wireless power transfer link for a applications of mWatts devices
by: Adam, Ismail, et al.
Published: (2018)

Linearizing techniques for sensor output
by: Saddiqi, Mohammad Tahir, et al.
Published: (2011)

Power supply power-supply interference in smart sensors-to-microntroller interface for biomedical signals
by: Ashraful, Muhammad, et al.
Published: (2011)

Response and inaccuracy issues of sensors
by: Ashraful, Muhammad, et al.
Published: (2011)

DC-DC boost converter for grid-tied renewable energy generation systems
by: Shahid, Zeeshan, et al.
Published: (2014)

Development of air quality measurement system using raspberry Pi
by: Mohd Pu'ad, Muhamad Farhan, et al.
Published: (2018)

Real time telemedical health care systems with wearable sensors
by: Fajingbesi, Fawwaz Eniola, et al.
Published: (2017)