Surface modification of titanium alloy through electrical discharge machining (EDM)

QR Code

Surface modification of titanium alloy through electrical discharge machining (EDM)

This paper presents investigation on the alloying capability of Cu-TaC electrode during electrical discharge machining (EDM). The electrode produced through powder metallurgy technique was used in machining alpha-beta titanium alloy (Ti-6Al-4V) under different machining conditions. EDM experiments w...

Full description

Bibliographic Details
Main Authors:	Ndaliman, Mohammed Baba, Khan, Ahsan Ali, Ali, Mohammad Yeakub
Format:	Article
Language:	English
Published:	University of Malaya 2011
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/21469/ http://irep.iium.edu.my/21469/1/Mohammad_Febryary_2012.pdf

Similar Items

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Surface modification by EDM using Co-Cr sintered powder metallurgy electrode
by: Khan, Ahsan Ali, et al.
Published: (2012)

Surface modification by EDM using CO-CR sintered powder metallurgy electrod
by: Khan, Ahsan Ali, et al.
Published: (2012)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Developments in EDM process variables
by: Khan, Ahsan Ali, et al.
Published: (2011)

Determination of influential factors on EDMed surface properties using Plackett-Burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Determination of influential factors on edmed surface properties using plackett-burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Analyzing the influence of electrical parameters on EDM process of Ti6Al4V alloy using Adaptive Neuro-fuzzy Inference System (ANFIS)
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2015)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Influence of electrode cooling on material migration among the electrodes during edm of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode cooling on material migration among the electrodes during EDM of titanium alloy
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrodes for EDM
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Development of Powder Metallurgy (PM) compacted Cu-TaC electrode for EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2011)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
by: Khan, Ahsan Ali, et al.
Published: (2013)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Performance of PM compacted Cu-TaC electrodes during EDM
by: Mohammed, Baba Ndaliman, et al.
Published: (2011)

Influence of electrode cooling on recast layers and micro crack in EDM of titanium
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Influence of thermal conductivity cf electrodes on EDM process parameters
by: Khan, Ahsan Ali, et al.
Published: (2012)