Effects of austempering treatment on mechanical properties of
ductile iron

QR Code

Effects of austempering treatment on mechanical properties of ductile iron

Bibliographic Details
Main Authors:	Ahmed Ghazal, Belal, Adesta, Erry Yulian Triblas
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/21357/ http://irep.iium.edu.my/21357/1/20.pdf

Similar Items

The effect of deep cryogenic treatment on the properties of AISI D2 tool steel
by: Ahmed Ghazal, Belal, et al.
Published: (2011)

An investigation on the surface austempering of ductile cast iron
by: Fayyaz, Abdolali, et al.
Published: (2017)

The effects of niobium addition on mechanical and physical properties of austempered ductile iron / Siti Khadijah Alias
by: Alias, Siti Khadijah
Published: (2010)

The effect of deep cryogenic treatment on the properties of AISI D2 tool steel
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Investigation of ductile iron in mold treatment process parameter
by: Yap, Min Choo
Published: (2009)

Investigation of ductile iron 'sandwich' treatment process parameter
by: Md Fakhrurazi, Abdul Halil
Published: (2009)

New heat treatment technique (tempering-austempered in single treatment) for matrix transformation and mechanical properties of ductile iron / Bulan Abdullah … [et al.]
by: Abdullah, Bulan, et al.
Published: (2013)

Effect of welding process on formability of tailor welded blanks
by: Mushtaq, Umer, et al.
Published: (2011)

Investigation of thin wall ductile iron parameter
by: Mohd Khairi, Mohd Noor
Published: (2009)

Indentation mechanism in rotary hammer forging process: analytical and numerical approach
by: Saud FEMD Alazemi, Saud, et al.
Published: (2018)

The effect of stucco system in ceramic shell investment casting
by: Mohamad Badari, Siti Norbahiyah, et al.
Published: (2011)

The project management challenges in technology innovation
by: Mahmood, Mahmood Hameed, et al.
Published: (2011)

Low temperature solder alloys for ultrasonic soldering of glass
by: Mustafa, Yusri, et al.
Published: (2015)

The evaluation of lean manufacturing implementation and their impact to manufacturing performance
by: Adesta, Erry Yulian Triblas, et al.
Published: (2018)

Hardware improvement of FDM 3D printer: issue of bed leveling failures
by: Arief, Rudi Kurniawan, et al.
Published: (2019)

In-Situ syntheses of high wear resistant coating reinforced Ti-6al-4v Matrix
by: Ahmed Ghazal, Belal, et al.
Published: (2011)

Toolpath strategy for cutter life improvement in plunge milling of AISI H13 tool steel
by: Adesta, Erry Yulian Triblas, et al.
Published: (2018)

The Development of Cost Structure for High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2008)

The study of the implementation of OHSAS : 18001 at Kulliyyah of Engineering (KOE)
by: Wan Yusoff, Wan Ahmad Yusmawiza, et al.
Published: (2011)

Critical chain in project management
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

An investigation on low-temperature thermochemical treatments of austenitic stainless steel in fluidized bed furnace
by: Haruman, Esa, et al.
Published: (2012)

New approach in cost structuring of high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Flank Wear Modeling in High Speed Hard Turning by using artificial Neural Network and Regression Analysis
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

A feasibility study on low temperature thermochemical treatments of Austenitic Stainless Steel in Fluidized Bed Furnace
by: Haruman, Esa, et al.
Published: (2011)

Effect of Inoculation On Microstructure, Mechanical and Corrosion Properties of High Manganese Ductile Ni-resist Alloy
by: Mohd Rashidi, Maarof, et al.
Published: (2013)

Influence of backcutting phenomena to surface roughness of hardened AISI H13 during high speed end milling process
by: Mohd Ali, Afifah, et al.
Published: (2011)

An improvement of mechanical properties of ductile iron and niobium alloyed ductile iron through new heat treatment cycles / Bulan Abdullah
by: Abdullah, Bulan
Published: (2011)

An improvement of mechanical properties of ductile iron and niobium alloyed ductile iron through new heat treatment cycles / Bulan Abdullah
by: Abdullah, Bulan
Published: (2012)

Cutting force impact to tool life of CT5015 in high speed machining by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2012)

Experimental investigation on frequency shifting of imperfect adhesively bonded pipe joints
by: Haiyam, F. N., et al.
Published: (2018)

Tool life estimation model based on simulated flank wear during high speed hard turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2010)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Experimental investigations in high-speed hard turning of AISI 4340 steel using mixed ceramic
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of tooling cost model in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Development of new model for cutting force in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Cutting temperature and surface roughness optimization in CNC end milling using multi objective genetic algorithm
by: Al Hazza, Muataz, et al.
Published: (2012)