Modeling of compression systems

QR Code

Modeling of compression systems

Bibliographic Details
Main Author:	Idres, Moumen
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/21075/ http://irep.iium.edu.my/21075/1/Chapter_5.pdf

Similar Items

Introduction to compressors
by: Idres, Moumen
Published: (2011)

Three-dimensional analysis of compressors
by: Idres, Moumen
Published: (2011)

Rotating stall and surge
by: Idres, Moumen
Published: (2011)

Compressor models
by: Idres, Moumen
Published: (2011)

Dynamic thermal model for proton-exchange membrane fuel cell
by: Mohamed Idres, Moumen, et al.
Published: (2010)

Constrained model predictive control for proton exchange membrane fuel cell
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Air supply system transient model for proton exchange membrane fuel cell
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Fuel cell starvation control using model Predictive technique with laguerre and exponential weight functions
by: Abdullah, Muhammad Faris, et al.
Published: (2014)

Air supply system transient model for proton exchange membrane fuel cell
by: Mahmoud Idres, Moumen Mohammed, et al.
Published: (2011)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Particle swarm optimization of micro air launch vehicle trajectory
by: Omar, Hanafy, et al.
Published: (2011)

One-dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-based thermoelectrically controlled micronozzle
by: Hameed, Ammar, et al.
Published: (2012)

Particle Swarm-Based Micro Air Launch Vehicle Trajectory Optimization Method
by: Omar, Hanafy, et al.
Published: (2012)

Surge and rotating stall
by: Idres, Moumen
Published: (2011)

One dimensional analysis of thermoelement exposed to lateral heat transfer as a wall in MEMS-Based thermoelectrically controlled micronozzle
by: Mohammed Idres, Moumen, et al.
Published: (2011)

Effectiveness of wheel-typed grain design for hybrid rocket motor performance
by: Kafafy, Raed Ismail, et al.
Published: (2013)

Simulation of wheel type fuel grain in hybrid rocket motor
by: Azami, Muhammad Hanafi, et al.
Published: (2013)

Hybrid rocket performance with varying additive concentrations
by: Kafafy, Raed, et al.
Published: (2013)

Development of economical vehicle model for pedestrian-friendly front-end profile study
by: Kausalyah, Venkatason, et al.
Published: (2014)

Development and optimization of a vehicle front-end geometry model for improved pedestrian safety
by: Abdullah, Kassim Abdulrahman, et al.
Published: (2014)

Particle swarm optimization of air-launch vehicle and trajectory
by: Aldheeb, M, et al.
Published: (2011)

On the scaling of air launch vehicles
by: Kafafy, Raed, et al.
Published: (2011)

Numerical simulation and validation of high-speed turbulent and chemically-reacting flows
by: Kamel, Mohammed, et al.
Published: (2015)

Numerical simulation of supersonic and turbulent combustion with trans-verse sonic fuel injection
by: Kamel, Mohammed, et al.
Published: (2015)

Effect of varying design options on the transient behavior of a hybrid rocket motor
by: Kafafy, Raed Ismail, et al.
Published: (2014)

Towards a numerical simulation of supersonic mixing & combustion
by: Kamel, Mohammed, et al.
Published: (2013)

Two-dimensional flow properties of micronozzle under varied isothermal wall conditions
by: Hameed, Amar Hasan, et al.
Published: (2011)

Frequency estimation of flow induced vibration in thin cantilever plate
by: Javeed, Abdulhakeem, et al.
Published: (2013)

Experimental investigation of the performance of flutter-based microgenerators
by: Kafafy, Raed, et al.
Published: (2013)

Development of compressed air powered engine system based on subaru ea71 model
by: Chen, Rui
Published: (2013)

Design and development of a compressed air machine using a compressed air energy storage system
by: Abdul Aziz, M., et al.
Published: (2015)

Design optimization of Micro Air Launch Vehicle using differential evolution
by: Aldheeb, Mohammed, et al.
Published: (2012)

Performance analysis of a small capacity horizontal axis wind turbine using QBlade
by: Ali, Said, et al.
Published: (2019)

Design, fabrication and flight testing of a surveillance UAV
by: Idres, Moumen, et al.
Published: (2015)

Three-dimensional vibration analysis of fluid-filled pipes
by: Kolo, Isa, et al.
Published: (2013)

Development of generic algorithm in wheel-typed hybrid rocket grain design for performance estimation
by: Kafafy, Raed, et al.
Published: (2012)

Speech coding using compressive sensing on a multicore system
by: Gunawan, Teddy Surya, et al.
Published: (2011)

A Review of Compressed-air Hybrid Technology in Vehicle System
by: F., Wasbari, et al.
Published: (2017)

Effect of Compression Ratio on Compression Ignition Engine Performance Operating with Biofuel
by: Akasyah, M Khathri, et al.
Published: (2014)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)