Modeling and analysis of MRR, EWR and surface roughness in
EDM milling through response surface methodology

QR Code

Modeling and analysis of MRR, EWR and surface roughness in EDM milling through response surface methodology

Electrical Discharge Machining (EDM) has grown over the last few decades from a novelty to a mainstream anufacturing process. Though, EDM process is very demanding but the mechanism of the process is complex and far from completely understood. It is difficult to establish a model that can accurate...

Full description

Bibliographic Details
Main Authors:	Asif Iqbal, A.K.M., Khan, Ahsan Ali
Format:	Article
Language:	English
Published:	Science Publications 2010
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/1881/ http://irep.iium.edu.my/1881/1/Asif_2.pdf

Similar Items

Investigation on the surface finish, MRR and the surface damage during the EDM of tungsten carbide
by: Khan, Ahsan Ali, et al.
Published: (2011)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Determination of influential factors on EDMed surface properties using Plackett-Burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Determination of influential factors on edmed surface properties using plackett-burman design
by: Ndaliman, Mohammed Baba, et al.
Published: (2012)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Investigation of surface roughness in micro-EDM of nonconductive ZrO2 ceramic with powder mixed dielectric fluid
by: Sabur, Abdus, et al.
Published: (2015)

Surface modification by EDM using Co-Cr sintered powder metallurgy electrode
by: Khan, Ahsan Ali, et al.
Published: (2012)

Surface modification by EDM using CO-CR sintered powder metallurgy electrod
by: Khan, Ahsan Ali, et al.
Published: (2012)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Surface roughness optimization using Taguchi method of high speed end milling for hardened steel D2
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2017)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

A comparative study on work surface hardness EDMed by Ta-C powder compacted and copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Investigation of magnetic field effect on MRR, EWR and surface roughness during EDM of AISI420 tool Steel
by: Efendee, A. M., et al.
Published: (2021)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Development of surface roughness prediction model for high speed end milling of hardened tool steel
by: Mohd Ali , Afifah, et al.
Published: (2011)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Cutting temperature and surface roughness optimization in CNC end milling using multi objective genetic algorithm
by: Al Hazza, Muataz, et al.
Published: (2012)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Developments in EDM process variables
by: Khan, Ahsan Ali, et al.
Published: (2011)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Effect of cutting parameters on surface roughness in end milling of AlSi/AlN metal matrix composite
by: Tomadi, Siti Haryani, et al.
Published: (2017)

Statistical approach to modeling & optimization of surface roughness in high speed end milling of silicon with diamond coated tools
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Significant parameters for the surface roughness in incremental forming process
by: Echrif, Salah B. M., et al.
Published: (2014)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

Effect of size and shape of electrodes on the performance of EDM
by: Khan, Ahsan Ali, et al.
Published: (2008)

Influence of magnetic field on reduction chatter and of surface roughness in end milling of Titanium Alloy - Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

Surface roughness optimization in end milling of stainless steel AISI 304 with uncoated WC-Co insert under magnetic field
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Surface roughness model for high speed end milling of soda lime glass using carbide coated tools with compressed air blowing
by: Mahmud, M. A., et al.
Published: (2012)