Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel

QR Code

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel

In the area of grit blasting, it is well known that microscopically small abrasive debris gets trapped on the surface, and due to impact the grits might cause the surface to fracture and a fraction of it to be embedded. The same problem appears in abrasive water jet (AWJ) machining especially in the...

Full description

Bibliographic Details
Main Authors:	Mohd Ali, Afifah, Khan, Ahsan Ali, Mohammad , Yeakub Ali
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2011
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/1877/ http://irep.iium.edu.my/1877/1/Afifa%2C_Ahsan%2C_Yeakub.pdf

Similar Items

Performance of different abrasive materials during abrasive water jet machining of glass
by: Khan, Ahsan Ali, et al.
Published: (2007)

A study on abrasive water jet machining of aluminum with garnet abrasives
by: Khan, Ahsan Ali, et al.
Published: (2005)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Effect of Process Parameters on Abrasive Contamination During Water Abrasive Jet Machining of Mild Steel
by: Afifah, Ali, et al.
Published: (2010)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Formation of micro-cracks and recast layer during EDM of mild steel using copper electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Influence of current, spark on-time and off-time on electrode wear during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Features of electrode wear during EDM of mild steel with TaC-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Features of EDM of mild steel with Ta-Cu powder compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Optimization of process parameters on EDM milling of stainless steel AISI 304
by: A.K.M, Asif Iqbal, et al.
Published: (2011)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

A new approach of applying cryogenic coolant in turning AISI 304 stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

Application of silicon carbide in abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2011)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

The effects of process variables on the hardness of nitrided 3% chromium steel
by: Mridha, Shahjahan, et al.
Published: (2008)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)