Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining

QR Code

Experimental investigation of machining parameters on surface roughness in dry and wet wire-electrical discharge machining

Wire electrical discharge machining (WEDM) is a thermal process in which the workpiece and the wire (tool) experience an intense local heating in the discharge channel. The high power density results in the erosion of a part of the material from both electrodes by local melting and vaporization. Wh...

Full description

Bibliographic Details
Main Authors:	Abdulkareem, Suleiman, Khan, Ahsan Ali, Mohd Zain, Zakaria
Format:	Article
Language:	English
Published:	Trans Tech Publications 2011
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/1868/ http://irep.iium.edu.my/1868/1/Suleiman%2C_Ahsan%2C_Zakaria.pdf

Similar Items

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Influence of electrode profiles on electrical discharge machining of titanium
by: Zain, Zakaria Mohd, et al.
Published: (2011)

Temperature distribution in copper electrode during electrical discharge machining process
by: Abdulkareem, Suleiman, et al.
Published: (2017)

Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining
by: Abdulkareem, Suleiman, et al.
Published: (2009)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Influence of process parameters on electrical discharge machined job surface integrity
by: Iqbal, A.K.M. Asif, et al.
Published: (2010)

Investigation of kerf in micro wire electro discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Analysis of microlayer defects of a functionally graded titanium alloy by electrical discharge machining
by: Abdulkareem, Sulaiman, et al.
Published: (2018)

Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Influence of work and tool materials on parameters of electrical discharge machining(EDM)
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Role of heat transfer on process characteristics during electrical discharge machining
by: Khan, Ahsan Ali
Published: (2011)

Surface Modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface modification using Electric Discharge Machining (EDM) with powder addition
by: Khan, Ahsan Ali, et al.
Published: (2011)

Modeling of EDM Process parameters for Machining Stainless Steel using Copper Electrodes
by: Khan, Ahsan Ali, et al.
Published: (2008)

Influence of TaC Powder Additive on electrical discharge machining of stainless Steel
by: Mohd Zain, Zakaria, et al.
Published: (2011)

Surface modification of titanium alloy through electrical discharge machining (EDM)
by: Ndaliman, Mohammed Baba, et al.
Published: (2011)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining
by: Mohd Zain, Zakaria, et al.
Published: (2014)

Influence of the angle of cut of workpiece on taper and corner roundness during Wire Electrical Discharge Machining (WEDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy
by: Mohammed , Baba Ndaliman, et al.
Published: (2013)

Tool wear rate during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Enhancement of machining performance during electrical discharge machining of stainless steel with carbon nanotube powder added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Micro wire electro discharge grinding: optimization of material removal rate and surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Wear ratio and work surface finish during electrical discharge machining (EDM) with eccentric electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

Relationship between machining variables and process characteristics during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2011)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd Zain, Zakaria, et al.
Published: (2012)

Electro-discharge machining of SUS 304 stainless steel with TaC powder-mixed dielectric
by: Mohd. Zain, Zakaria, et al.
Published: (2012)

Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
by: Mohammed Baba, Ndaliman, et al.
Published: (2011)

Investigation of the influence of the properties of the work and tool materials on performance level of Electrical Discharge Machining (EDM) process
by: A.K.M., N. Amin, et al.
Published: (1997)

Effect of gap voltage and pulse-on time on material removal rate for electrical discharge machining of Al2O3
by: Moudood, M. A., et al.
Published: (2015)

Prediction of surface roughness of Ti-6Al-4V in electrical discharge machining: A regression model
by: Rahman Khan, Md. Ashikur, et al.
Published: (2011)

Effect of abrasive water jet machining parameters on aramid fibre reinforced plastics composite
by: Azhari , Mohd Azmir, et al.
Published: (2009)

Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining
by: Mohd Azhari, Mohd Azmir, et al.
Published: (2008)

Effect of process parameters on abrasive contamination during water abrasive jet machining of mild steel
by: Mohd Ali, Afifah, et al.
Published: (2011)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Significant parameters for the surface roughness in incremental forming process
by: Echrif, Salah B. M., et al.
Published: (2014)