Sample preparation on ceramics composite for cutting tools in high speed machining

QR Code

Sample preparation on ceramics composite for cutting tools in high speed machining

Bibliographic Details
Main Authors:	Sutjipto, Agus Geter Edy, Kaderi, Akbar
Format:	Book Chapter
Language:	English
Published:	IIUM Press 2011
Subjects:	TS Manufactures
Online Access:	http://irep.iium.edu.my/18108/ http://irep.iium.edu.my/18108/1/5.pdf

Similar Items

Coating for high speed cutting tools
by: -, Suryanto
Published: (2011)

The effect of CaO addition on the microstructural, mechanical and dielectric properties of pure MgO ceramic
by: Sutjipto, Agus Geter Edy
Published: (2007)

The strength of SiO2 added MgO ceramics to withstand flashover-treeing appearance under electron bombardment in vacuum
by: Sutjipto, Agus Geter Edy
Published: (2004)

Development of ceramics cutting tool for machining using aluminium oxide reinforced with copper powder
by: Muhammad Aiman, Ishak
Published: (2016)

Cutting force impact to tool life of CT5015 in high speed machining by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2012)

High wear Resistant Ceramic Cutting inserts With Enhanced Toughness For High-Speed Machining
by: Ahmad, Zainal Arifin, et al.
Published: (2016)

Study on metal removing from alumina ceramics
by: Sutjipto, Agus Geter Edy, et al.
Published: (2011)

The use of SEM to investigate the effect of an electron beam on the optically-visible flashover treeing of MgO ceramic
by: Sutjipto, Agus Geter Edy, et al.
Published: (2007)

Study Of Cutting Edge Temperature And Cutting Force Of End Mill Tool In High Speed Machining
by: Mohammad Ashaari, Kiprawi, et al.
Published: (2017)

Cutting tool angle of lathe machine for different materials
by: Normawati, Mansor
Published: (2008)

Effects of Irregular Tool Geometry and Machining Process Parameters on the Wavelength Performance of Process Damping in Machining Titanium Alloy at Low Cutting Speed
by: Muhammad Adib , Shaharun, et al.
Published: (2015)

Capabilities of cermets tools for high speed machining of austenitic stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2006)

Experimental investigation of chip tool contact process and determination of optimum cutting speed for steel of any composition
by: Amin, A. K. M. Nurul, et al.
Published: (1990)

High strength inert ceramic balls
by: Sutjipto, Agus Geter Edy, et al.
Published: (2021)

Sample preparation of TiO2 added ZnO using powder metallurgy route and its characteristics
by: Sutjipto, Agus Geter Edy, et al.
Published: (2020)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

Effect of High-Speed Milling Tool Path Strategies on the Surface Roughness of Stavax ESR Mold Insert Machining
by: Mebrahitom, A., et al.
Published: (2016)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Influence of work material, cutting conditions and rigidity of tool holders on machine tool chatter
by: Amin, A. K. M. Nurul
Published: (1992)

Processing And Properties Of Ni/YSZ Composite Coating On High Speed Steel Cutting Tool

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

Surface breakdown property of SiO2 added MgO under electron bombardment in vacuum: a promising materials for spacecraft and space station
by: Sutjipto, Agus Geter Edy
Published: (2007)

The possibility of utilizing scanning electron microscope for materials characterization
by: Sutjipto, Agus Geter Edy
Published: (2011)

Recent finding on premature failure of commercial electric motor bearings
by: Sutjipto, Agus Geter Edy
Published: (2010)

Influences of Varying Combination of Feed Rate and Depth of Cut to Tool Wear Rate and Surface Roughness: High Speed Machining Technique in Non-High Speed Milling Machine
by: Mohd Zairulnizam, Mohd Zawawi, et al.
Published: (2014)

High speed cutting: an approach towards improved machining performance
Published: (2011)

Cryogenic machining performance of M303 at high cutting speeds
by: Nur Fadhilah Aimuni Mohd Ridzuan,, et al.
Published: (2024)

Development of Cu-SiC composite for electrical discharge machining electrode using powder metallurgy technique
by: Ahmad Razi, Fatimah Azreen, et al.
Published: (2012)

Effects of tool path strategies on surface roughness in high speed milling
by: Abdul Rashid, Muhammad
Published: (2012)

Machining Time Simulation in High Speed Hard Turning
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Tool Wear Observation During Unconventional Low Speed Machining Using Low Cost Micromilling
by: Ainur Munira, Rosli, et al.
Published: (2021)

Development of new model for cutting force in high speed hard turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2011)

Suppression of Chatter in High Speed Milling Machine Using Spindle Speed Variation Method with Acoustic Feedback PID Controller
by: Suparmaniam, Madan Varmma, et al.
Published: (2019)

Effect of Dry Cutting on Force and Tool Life when Machining Aerospace Material
by: K., Kadirgama, et al.
Published: (2010)

Tool life in high speed turning with negative rake angle
by: Adesta, Erry Yulian Triblas, et al.
Published: (2011)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

Performance evaluation of coated ceramic cutting tools with T-land edge preparation when turning hardened tool steel
by: Wan Abdul Rahaman, Wan Emri
Published: (2006)

Multi-response optimizations for high speed ductile mode machining of soda lime glass
by: Bagum, Nasima, et al.
Published: (2015)

Microstructure and electrical properties of AZO films prepared by RF magnetron sputtering
by: Bakri, Jufriadi, et al.
Published: (2011)

Study on Optimal Surface Property Of WC-Co Cutting Tool for Aluminium Alloy Cutting
by: Mohd, Nizar, et al.
Published: (2016)