Prediction of tool life and experimental investigation during hot milling of AISI H13 tool steel

QR Code

Prediction of tool life and experimental investigation during hot milling of AISI H13 tool steel

This paper presents the results of experimental investigations conducted on a vertical machining centre (VMC) using spindle speed, feed rate, and depth of cut as machining variables to ascertain the effectiveness of TiAlN insert in end milling of hardened steel AISI H13, under workpiece preheated co...

Full description

Bibliographic Details
Main Authors:	Amin, A. K. M. Nurul, Hafiz, A.M.K., Lajis, M.A., Patwari, Anayet U.
Format:	Article
Language:	English
Published:	Trans Tech Publications, Switzerland 2010
Subjects:	TJ Mechanical engineering and machinery TS Manufactures
Online Access:	http://irep.iium.edu.my/16680/ http://irep.iium.edu.my/16680/1/AMR_2010_-_Prediction_of_TL_n_Experimental_Investigation_During_Hot_Milling_of_AISI_H13.pdf

Similar Items

Prediction of tool life and experimental investigation and prediction of tool life during hot milling of AISI H13 tool steel
by: A.K.M., Nurul Amin, et al.
Published: (2010)

Modeling of surface roughness during end milling of AISI H13 hardened tool steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Development of tool life prediction model of TiAlN coated tools during the high speed hard milling of AISI H13 steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Development of tool life prediction model for PCBN inserts during the high speed end milling of AISI H13 hardened tool steel
by: Hafiz, A.M. Khalid, et al.
Published: (2007)

Development of tool life prediction model of TIALN coated tools during the high speed hard milling of AISI H13 steel
by: Khalid, A. K. H., et al.
Published: (2007)

Machinability improvement by workpiece preheating during end milling AISI H13 hardened steel
by: Mokhtar, Suhaily, et al.
Published: (2011)

A new technique to improve the machinability of hardened steel AISI H13 in end milling
by: Amin, A. K. M. Nurul, et al.
Published: (2010)

Development of surface roughness prediction model using response surface methodology in high speed end milling of AISI H13 tool steel
by: Hafiz, A. K. M., et al.
Published: (2007)

Prediction of tool life in end milling of hardened steel AISI D2
by: Lajis, M.A., et al.
Published: (2008)

Prediction of surface roughness in hard milling of AISI D2 tool steel
by: Lajis, M. A., et al.
Published: (2007)

Modelling of tool life by response surface methodology in hard milling of AISI D2 tool steel
by: Lajis, M. Amri, et al.
Published: (2011)

Prediction of tool life in end milling of hardened steel AISI D2
by: Lajis, M. A., et al.
Published: (2008)

Modelling and optimization of tool life in end milling of AISI 02 hardened steel
by: Lajis, M. A., et al.
Published: (2008)

Toolpath strategy for cutter life improvement in plunge milling of AISI H13 tool steel
by: Adesta, Erry Yulian Triblas, et al.
Published: (2018)

Modelling of tool life by response surface methodology in hard milling of Aisi D2 tool steel
by: Lajis, Mohd Amri, et al.
Published: (2007)

Hot machining in end milling of hardened steel AISI D2
by: Lajis, M. A., et al.
Published: (2008)

Content comparative investigation on tool wear during end milling of AISI H13 steel with different tool path strategies
by: Adesta, Erry Yulian Triblas, et al.
Published: (2017)

Cost Model for end-milling of AISI D2 tool steel
by: Mohamed, Elhadie, et al.
Published: (2011)

Development of mathematical cost model for preheated end-milling of AISI D2 tool steel
by: El-hadie, Mohamed, et al.
Published: (2011)

Preheated machining in end milling of hardened steel AISI D2
by: Lajis, M. A., et al.
Published: (2008)

Machinability aspects in heat assisted machining of hardened steel AISI H13 using coated carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Development of mathematical cost model for room temperature end-milling of AISI D2 tool steel
by: El-hadie, M, et al.
Published: (2011)

Heat assisted machining of hardened steel AISI H13 for longer tool life and higher efficiency in die and mould making
by: Amin, A. K. M. Nurul
Published: (2012)

Tool wear and surface roughness aspects in heat assisted end milling of AISI D2 hardened steel
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Surface Modiﬁcation of AISI H13 Tool Steel by Laser Cladding with NiTi Powder
by: B., Norhafzan, et al.
Published: (2016)

Surface modification of AISI H13 tool steel by laser cladding with NiTi powder
by: Norhafzan, Bariman, et al.
Published: (2016)

Mathematical model for the prediction of chip serration frequency in end milling of steel AISI1020
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2009)

Computational analysis for the prediction chip serration frequency in end milling of steel AISI1020
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

Theoretical and experimental investigation in prediction of tool life in preheated machining of AISI 02 hardened steel
by: Lajis, M. A., et al.
Published: (2008)

Development of surface roughness prediction model using response surface methodology in high speed end milling of AISI HI3 tool steel
by: Hafiz, A.M. Khalid, et al.
Published: (2007)

Preheating in end milling of AISI D2 hardened steel with coated carbide inserts
by: Lajis , M.A., et al.
Published: (2010)

The effect of tool path strategies on cutting temperature and cutting force during pocket milling of AISI H13
by: Adesta, Erry Yulian Triblas, et al.
Published: (2016)

Surface integrity in hot machining of AISI D2 hardened steel
by: Lajis, Mohd Amri, et al.
Published: (2012)

Laser surface modification of Yttria Stabilized Zirconia (YSZ) thermal barrier coating on AISI H13 tool steel substrate
by: Reza, M. S., et al.
Published: (2018)

Thermal Barrier Coatings on Laser Surface Modified AISI H13 Tool Steel Using Atmospheric Plasma Spray Technique
by: Reza, M. S., et al.
Published: (2013)

Prediction model of cutting force by cutting parameters using response surface methodology in end milling of steel AISI 1020
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2008)

A new technique for the investigation of chatter formation during end milling of medium carbon steel (AISI 45)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Thermally-Induced Crack Evaluation in H13 Tool Steel
by: Abdulhadi, Hassan Abdulrssoul, et al.
Published: (2017)

Comparison of the cutting force, power, tool life and torque in the end milling of modified AISI P20 tool steel
by: P. Vinothi, S Parawa Karan
Published: (2009)

Multi-criteria optimization in end milling of AISI D2 hardened steel using coated carbide inserts
by: Karim, A.N. Mustafizul, et al.
Published: (2011)