Effectiveness of uncoated WC-Co and PCD inserts in end milling of aluminum silicon carbide (AlSiC)

QR Code

Effectiveness of uncoated WC-Co and PCD inserts in end milling of aluminum silicon carbide (AlSiC)

Metal matrix composite (MMC) with silicon carbide (SiC) reinforcement in pure aluminum matrix have found wide application in the automotive industry, especially in fiber reinforced pistons and particle-strengthened brake discs. Silicon carbide (SiC) reinforcement provides improved mechanical propert...

Full description

Bibliographic Details
Main Authors:	M. K., Nor Khairusshima, Amin, A. K. M. Nurul, Ismail, Ahmad Faris
Format:	Article
Language:	English
Published:	Elsevier 2007
Subjects:	TS200 Metal manufactures. Metalworking
Online Access:	http://irep.iium.edu.my/16501/ http://irep.iium.edu.my/16501/1/Shima_paper_for_AMPT_2008.pdf

Similar Items

PCD inserts in end milling of Aluminum Silicon Carbide (AlSiC)
by: M. K. , Nor Khairusshima, et al.
Published: (2011)

Performance of uncoated WC-Co in end milling of Aluminium Silicon Carbide (AlSiC)
by: M. K. , Nor Khairusshima, et al.
Published: (2011)

Surface roughness optimization in end milling of stainless steel AISI 304 with uncoated WC-Co insert under magnetic field
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Influence of preheating on performance of circular carbide inserts in end milling of carbon steel
by: A.K.M., Nurul Amin, et al.
Published: (2007)

Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2009)

Tool life assessment in end milling titanium alloy (Ti-6Al-4V) using PCD inserts
by: Turnad L., Ginta, et al.
Published: (2008)

Study on tool wear and tool life during milling JFRP using uncoated carbide cutting tool
by: Rashid, Mohammed Abdur N., et al.
Published: (2018)

Optimization of surface roughness in micro-high speed end milling of soda lime glass using uncoated tungsten carbide tool with compressed air blowing
by: Amin, A. K. M. Nurul, et al.
Published: (2014)

Modeling for surface roughness in end-milling of titanium alloy Ti-6AI-4V using uncoated WC-Co and PCD Inserts
by: Ginta, Turnad Lenggo, et al.
Published: (2007)

A comparative study on flank wear of ceramic and Tungsten carbide inserts during high speed machining of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2018)

Comparison of surface roughness in end milling of titanium alloy Ti-6Al-4V using uncoated WC-Co and PCD inserts through generation of models
by: Ginta, Turnad Lenggo, et al.
Published: (2011)

Analysis of Machinability of Inconel 718 in High Speed End Milling with Ceramic Inserts Under Room Temperature Conditions
by: Nurul Amin, A. K. M, et al.
Published: (2012)

Surface roughness model for high speed end milling of soda lime glass using carbide coated tools with compressed air blowing
by: Mahmud, M. A., et al.
Published: (2012)

Investigation of the effects of machining parameters and air blowing on surface topography in high speed end milling of silicon
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Statistical approach to modeling & optimization of surface roughness in high speed end milling of silicon with diamond coated tools
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2013)

Effect of cutting parameters on surface roughness in end milling of AlSi/AlN metal matrix composite
by: Tomadi, Siti Haryani, et al.
Published: (2017)

Experimental determination of optimum cutting conditions in turning low alloyed steel with cemented carbide tool
by: Amin, A. K. M. Nurul, et al.
Published: (1987)

Effect of addendum parameters to the formability of aluminum AL 6303
by: , Afzeri, et al.
Published: (2011)

Surface roughness of Carbides produced by abrasive water jet machining
by: Khan, Ahsan Ali, et al.
Published: (2005)

Formation of nitrides and carbides on titanium alloy surface through EDM
by: Mohammed , Baba Ndaliman, et al.
Published: (2012)

Enhancing mechanical and structural properties of TiC inserts using microwave energy
by: Mohamed Ariff, Tasnim Firdaus, et al.
Published: (2011)

Surface quality produced in EDM with tungsten carbide and copper compacted electrodes
by: Khan, Ahsan Ali, et al.
Published: (2015)

Identification of instabilities of the chip formation and it's prediction model during end milling of medium carbon steel (S45C)
by: Patwari, Muhammed Anayet Ullah, et al.
Published: (2010)

Investigation on the surface finish, MRR and the surface damage during the EDM of tungsten carbide
by: Khan, Ahsan Ali, et al.
Published: (2011)

A study on abrasive water jet machining of aluminum with garnet abrasives
by: Khan, Ahsan Ali, et al.
Published: (2005)

A study on material removal rate during EDM with tantalum carbide-copper compacted electrode
by: Khan, Ahsan Ali, et al.
Published: (2011)

The influence of welding condition on the microstructure of WC hardfacing coating on carbon steel substrate
by: Nagentrau, M., et al.
Published: (2019)

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC
by: Amin, A. K. M. Nurul, et al.
Published: (2002)

Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes
by: Khan, Ahsan Ali
Published: (2008)

Influence of chatter of VMC arising during end milling operation and cutting conditions on quality of machined surface
by: A.K.M, N. Amin, et al.
Published: (2001)

Improvements in the development of silicon nitride inserts using hybrid microwave energy for machining Inconel 718
by: Ariff, Tasnim Firdaus, et al.
Published: (2018)

Surface integrity in end milling titanium alloy Ti6Al4V under heat assisted machining
by: Ginta, Turnad Lenggo, et al.
Published: (2013)

Application of permanent magnets for chatter control in end milling of titanium alloy Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)

INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
by: Amin, A. K. M. Nurul, et al.
Published: (2016)

The effect of preheating of work on chatter during end milling of medium carbon steel performed on a Vertical Machining Center (VMC)
by: Amin, A. K. M. Nurul, et al.
Published: (2003)

A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
by: Khan, Ahsan Ali, et al.
Published: (2011)

Improved tool life in end milling ti-6al-4v through workpiece preheating
by: Ginta , Turnad L., et al.
Published: (2009)

Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2
by: Amin, A. K. M. Nurul, et al.
Published: (2008)

Influence of magnetic field on reduction chatter and of surface roughness in end milling of Titanium Alloy - Ti-6Al-4V
by: Sulaiman, Syidatul Akma, et al.
Published: (2012)