Investigation of finish cut of microelectrodischarge milling for nanosurface finish

QR Code

Investigation of finish cut of microelectrodischarge milling for nanosurface finish

In this article, the machining conditions to achieve nanometric surface roughness in finish cut microelectrodischarge milling were investigated. For a constant gap voltage, the effect of feed rate and capacitance was studied on average surface roughness (Ra) and maximum peak-to-valley roughness heig...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Mehfuz, R.
Format:	Article
Language:	English
Published:	A V S AMER INST PHYSICS, USA 2009
Subjects:	QC Physics TA Engineering (General). Civil engineering (General) TK Electrical engineering. Electronics Nuclear engineering
Online Access:	http://irep.iium.edu.my/14898/ http://irep.iium.edu.my/14898/4/JVST_B__2009_27%283%29_1330-1334.pdf

Similar Items

Investigation of finish cut of micro electro discharge milling for nano surface finish
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Finish cut of titanium alloy using micro electro discharge milling for nano surface finish
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Relationship between surface finish and chips
by: Abdul Gani, Haji Abd. Rahman.
Published: (2002)

Investigation of TWR for finish cut of titanium alloy using Micro Electro Discharge Milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Investigation of MRR for finish cut of titanium alloy using micro electro discharge milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Noble tool based micromilling for nanometric surface finish
by: Ali, Mohammad Yeakub
Published: (2011)

The effect of alloying element in lead-free solders on intermetallics growth with enimag surface finish
by: Jaidi, Zolhafizi
Published: (2020)

Effect of Multiple Reflow on IMC Formation using Various Surface Finishes
by: Siti Rabiatull Aisha, Idris, et al.
Published: (2013)

Parameter optimization of a cylindrical grinding operation for the quality of surface finish
by: Mohd Asrul, Abu Bakar
Published: (2010)

Experimental investigation on magnetorheological finishing process parameters
by: Abdul Wahab, Hashmi, et al.
Published: (2022)

Indoor fungal growth on variable antifungal at different wall finishing on plasterboard
by: Sunar, N.M., et al.
Published: (2018)

Field to finish : prosidur dan perlaksanaan menggunakan perisian CDS dan AutoCad
by: Mat Amin, Zulkarnaini
Published: (2005)

Finishing properties of oil based finishing material with different finishing systems on Sentang (azadirachta excelsa) / Siti Nur Madihah Mohd Fauzi
by: Mohd Fauzi, Siti Nur Madihah
Published: (2017)

Cutting Tools in Finishing Operations for CNC Rapid Manufacturing Processes: Simulation Studies
by: M. Nafis, O. Z., et al.
Published: (2014)

Micro electro discharge machining of micro pillar array: analysis of surface finish
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

A novel method for chatter control and improvement of surface finish in end milling
by: Amin, A. K. M. Nurul, et al.
Published: (2012)

Investigation of machining parameters for the multiple-response optimization of micro electrodischarge milling
by: Mehfuz, Reyad, et al.
Published: (2009)

Ranking Of Preferred Criteria Of Floor Finishes For Bathroom By The House Owner In East Coast Of The Malaysia
by: Ahmad, Farina Aisyah
Published: (2022)

Endurance limit of aluminum, brass and mild steel on different surface finish owing to cyclic loads
by: Ahmad Fitri, Zainal Abidin
Published: (2009)

Influence of nano powder mixed dielectric fluid on surface finish in micro electro discharge machining of zirconia
by: Ali, Mohammad Yeakub, et al.
Published: (2017)

Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2011)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Structural Analysis And Design Of Steel-Framed House With Cold-Formed And Hot-Finished Rectangular Hollow Section
by: Naaim, Nurfarhah
Published: (2019)

Magnetorheological finishing on metal surface: a review
by: N. A., Mutalib, et al.
Published: (2019)

Analysis of tool wear, cutting force, surface roughness and machining temperature during finishing operation of ultrasonic assisted milling (UAM) of carbon fibre reinforced plastic (CFRP)
by: Abd Halim, Nor Farah Huda, et al.
Published: (2017)

Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Sustainable Finished Product Optimization on Quality Response and Attitudinal Parameters
by: Nur Qurratul Ain, Adanan, et al.
Published: (2021)

Effect of ZnO Nano Materials on Grinding Surface Finishing
by: Yogeswaran, Muthusamy, et al.
Published: (2015)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Investigation of minimum chip thickness in micro end milling of PMMA: process development
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Combination of fused deposition modelling with abrasive milling for attaining higher dimensional accuracy and better surface finish
by: Amanullah Tomal, Abu Naser Mohammad, et al.
Published: (2018)

Effect of Multiple Reflow on Intermetallic Compound Formation using Various Surface Finishes
by: Siti Rabiatull Aisha, Idris, et al.
Published: (2011)

Development of Regression Equation for Surface Finish and Analysis of Surface Integrity in EDM
by: Khan, Md. Ashikur Rahman, et al.
Published: (2013)

Effect of abrasive tools on surface finishing when grinding mild steel
by: Abd Faiz, Muhammad
Published: (2010)

Deposition of Electroless Nickel Boron as Printed Circuit Board Surface Finish
by: Hardinnawirda, Kahar, et al.
Published: (2016)

Surface finish characteristics of titanium alloy in a non conventional technique
by: Md. Ashikur, Rahman Khan, et al.
Published: (2017)

An Experimental Investigation on Surface Finish in Die-Sinking EDM Of Ti-5Al-2.5Sn
by: Khan, Md. Ashikur Rahman, et al.
Published: (2015)

From farrow to finish.
by: Choo, Raymond Pow Yoon, et al.
Published: (2013)

Effect of machining parameters on the surface finish quality of natural fiber composites
by: Too, Mei Xian
Published: (2019)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)