Effect of conventional EDM parameters on micromachined surface roughness and fabrication of hot embossing master and microtool

QR Code

Effect of conventional EDM parameters on micromachined surface roughness and fabrication of hot embossing master and microtool

This article discusses the effect of conventional electrical discharge machining (EDM) parameters for generating micrometer and submicrometer leveled surface roughness. Fabrication of submillimeter-sized microstructure to use as a master microtool for replication of polymer microcomponents is also...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, S.M., Ammar
Format:	Article
Language:	English
Published:	Taylor & Francis 2009
Subjects:	T Technology (General)
Online Access:	http://irep.iium.edu.my/12524/ http://irep.iium.edu.my/12524/4/EffectofConventionEDM12524.pdf

Similar Items

Fabricating hot embossing micro tool using electrodischarge machining
by: Mohammad, Ammar Sami, et al.
Published: (2006)

Polymeric micro-fluidic channel by hot embossing
by: Mohammad, Amar Sami, et al.
Published: (2006)

Influence of machining parameters on surface roughness during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2011)

Optimization of EDM parameters for micro/meso fabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2006)

Developing a prototype micro hot embossing setup
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Investigation of micromachining of silicon using micro-EDM
by: Samykano, M., et al.
Published: (2011)

Experimental and Numerical Simulation of Hot Embossing for Fabrication of Glass Microlens Array
by: Lee, Helen May Shian, et al.
Published: (2022)

Hot embossing and injection molding of three-dimensional microcomponents
by: Ali, Mohammad Yeakub, et al.
Published: (2001)

Fabrication of glass microlens array using laser-assisted contactless hot embossing
by: Lee May Shian, Helen, et al.
Published: (2022)

Rapid Fabrication of Glass Micro and Nanostructures via Laser-assisted Hot Embossing
by: Lee, Helen May Shian, et al.
Published: (2023)

Micromachining
by: Ali, Mohammad Yeakub, et al.
Published: (2016)

Study of the effects of EDM parameters on material removal rate , electrode wear rate and surface roughness in the EDM of S-Star
by: Mohamed , Konneh
Published: (2010)

Examination of Machining Parameters on the Surface Roughness of Stavax ESR Materials using EDM
by: Mebrahitom, A., et al.
Published: (2014)

Hot Embossing of Micro Grating and Its Replication Accuracy
by: Muhammad Syahrir, Ahmad, et al.
Published: (2024)

The Effect of EDM with external magnetic field on surface roughness of stainless steel
by: Khan, Ahsan Ali, et al.
Published: (2013)

Investigation of micromachining of silicon using micro-EDM = penyelidikan dalam pemesinan mikro bagi silicon menggunakan EDM mikro
by: Mahendran, Samykano, et al.
Published: (2011)

Effect of machining parameters on surface roughness during wet and dry Wire-EDM of stainless steel
by: Abdulkareem, Suleiman, et al.
Published: (2011)

Focused ion beam micromachining of mems
by: Ali, Mohammad Yeakub
Published: (2008)

Relationship of surface roughness with current and voltage during wire EDM
by: Khan, Ahsan Ali, et al.
Published: (2006)

Optimization of Machining Parameters on Surface Roughness in EDM of Ti-6AI-4V using Response Surface Method
by: M. M., Rahman, et al.
Published: (2011)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Mohammed Baba, Ndaliman, et al.
Published: (2013)

Modelling the surface roughness behaviour of an EDMed workpiece with different tool electrodes using DoE
by: Ndaliman, Mohammed Baba, et al.
Published: (2013)

Influence of process parameters on surface integrity during EDM of mild steel
by: Khan, Ahsan Ali, et al.
Published: (2010)

Investigation of surface roughness in micro-EDM of nonconductive ZrO2 ceramic with powder mixed dielectric fluid
by: Sabur, Abdus, et al.
Published: (2015)

Modeling and analysis of MRR, EWR and surface roughness in EDM milling through response surface methodology
by: Asif Iqbal, A.K.M., et al.
Published: (2010)

Evaluation of glass nano/microstructures replication fidelity after laser-assisted hot embossing process
by: Lee, May Shian Helen
Published: (2023)

Investigation of microholes produced by focused ion beam micromachining
by: Mohd Fuad, Nurul Hajar, et al.
Published: (2011)

Investigation of Microholes Produced by Focused Ion Beam Micromachining
by: Mohd. Fuad, Nurul Hajar, et al.
Published: (2010)

Fabrication of micromachined uniform microtrench arrays for silicon based filtration membrane
by: Kamarul 'Asyikin Mustafa,, et al.
Published: (2019)

Focused ion beam micromachining: technology and application
by: Jaafar, Israd Hakim, et al.
Published: (2011)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Artificial intelligence model to predict surface roughness of Ti-15-3 alloy in EDM process
by: Khan, Md. Ashikur Rahman, et al.
Published: (2011)

Artificial intelligence model to predict surface roughness of Ti-15-3 alloy in EDM process
by: Khan, Md. Ashikur Rahman, et al.
Published: (2011)

Surface roughness studies in die-sink EDM of tungsten carbide using copper tungsten electrode
by: Konneh, Mohamed, et al.
Published: (2011)

Artificial Intelligence Model to Predict Surface Roughness of Ti-15-3 Alloy in EDM Process
by: Khan, Md. Ashikur Rahman, et al.
Published: (2011)

Effect of magnetic polarity on surface roughness during magnetic field assisted EDM of tool steel
by: A. M., Efendee, et al.
Published: (2018)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2018)

The influence of steel 35 wire EDM parameters on the surface roughness and morphology / Alexey A. Fedorov, Alexander V. Linovsky and Anatoliy P. Morgunov
by: Alexey A., Fedorov, et al.
Published: (2017)

Material removal rate of zirconia in electro discharge micromachining
by: Asfana, Banu, et al.
Published: (2015)