Form characterization of microhole produced by microelectrical discharge drilling

QR Code

Form characterization of microhole produced by microelectrical discharge drilling

This article discusses the characterization of form of microholes produced by microelectrical discharge drilling (micro-EDD) on beryllium-copper alloy using tungsten carbide electrode of 300 µm diameter. Using a fixed set of micro-EDD parameters, microholes of different aspect ratio were drilled. Th...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Hamad, Mohd Hosni, Karim, Ahmad Izwan
Format:	Article
Language:	English
Published:	Taylor & Francis 2009
Subjects:	TA Engineering (General). Civil engineering (General)
Online Access:	http://irep.iium.edu.my/1047/ http://irep.iium.edu.my/1047/1/Form_Characterization_of_Microhole_Produced_by.pdf

Similar Items

Geometrical integrity of microholes drilled by conventional and micro electrical discharge machining
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Geometrical integrity of microholes produced by micro-EDM
by: Ali, Mohammad Yeakub
Published: (2008)

Investigation of microholes produced by focused ion beam micromachining
by: Mohd Fuad, Nurul Hajar, et al.
Published: (2011)

Investigation of Microholes Produced by Focused Ion Beam Micromachining
by: Mohd. Fuad, Nurul Hajar, et al.
Published: (2010)

Microelectrical mechanical systems switch for designing multi-band antenna
by: Alam, A. H. M. Zahirul, et al.
Published: (2009)

Experimental study of electrical discharge drilling of stainless steel UNS S30400
by: Hanash, Ebrahim, et al.
Published: (2018)

Investigation of corner radius using micro wire electro discharge machine
by: Sabur, Abdus, et al.
Published: (2011)

Laser drilling of microholes in single crystal silicon using continuous wave (CW) 1070 nm fiber lasers with millisecond pulse widths
by: Maclean, Jessica O., et al.
Published: (2018)

Micro-drilling of metallic materials for microsystems technology
by: Ali, Mohammad Yeakub
Published: (2008)

Study on drilling induced delamination of woven kenaf fiber reinforced epoxy composite using carbide drills
by: Mokhtar, Suhaily, et al.
Published: (2018)

Micro electro discharge machining for nonconductive ceramic materials
by: Ali, Mohammad Yeakub
Published: (2017)

Micro electro discharge machining of non-conductive ceramic using conductive powder mix dielectric fluid
by: Ali, Mohammad Yeakub, et al.
Published: (2016)

Dry electrical discharge machining: an environmental friendly machining process
by: Ali, Mohammad Yeakub
Published: (2018)

High voltage discharge profile on soil breakdown using impulse discharge
by: Fajingbesi, Fawwaz Eniola, et al.
Published: (2017)

Effect of material thickness on Duration, hole characteristics, and drilling mechanism on micro-laser drilling
by: Haneef, Mohd Sabki
Published: (2023)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Surface roughness characterization on p20 tool steel in wirecut electrical discharge machining (wedm) process
by: Zaidatul Syima, Zainal
Published: (2013)

Fabrication of micro filter by electro discharge machining
by: -, Abdus Sabur, et al.
Published: (2011)

Morphological Characterization of Soil Penicillium sp. Strains - Potential Producers of Statin
by: Seydametova, Emine
Published: (2010)

Powder mixed micro electro discharge machining (PMμEDM)
by: Ali, Mohammad Yeakub
Published: (2011)

Simulating river discharge for Selangor River Basin
by: Azim Ashraf, Othman
Published: (2016)

Characterization of wrought aluminium feedstock billet produced by semisolid metal processing route
by: Benjunior, Bindamin
Published: (2021)

Investigation the delay of crack using stop drilled holes on mild steel
by: Ridzuan Shah Razi, Varathau Rajoo
Published: (2009)

Modeling of tool wear in drilling by statistical analysis and artificial neural network
by: SANJAY, C, et al.
Published: (2005)

Effect of discharge current and electrode size on material removal rate and wear ratio in electrical discharge machining
by: Khan, Ahsan Ali, et al.
Published: (2010)

Optimization of Electro Discharge Machining Parameters for Drilling Titanium in Small Holes Using Taguchi Method
by: Hazami, Che Hussain, et al.
Published: (2014)

GIS-based River Discharge Modelling
by: Akbari, Abolghasem
Published: (2016)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
by: Ali, Mohammad Yeakub
Published: (2009)

A study of surface roughness in drilling using mathematical analysis and neural networks
by: Sanjay, C., et al.
Published: (2006)

Investigate the effectiveness of stop drill hole in delaying crack from crack initiation
by: Syafiq, Hashim
Published: (2012)

Green curb - an alternative method to produce road curb using old tire
by: J., Izwan, et al.
Published: (2018)

Experimental study of conventional wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Simulation of Drill Cuttings Dispersion and Deposition in South China Sea
by: Hock, Lye Koh, et al.
Published: (2011)

Wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Micro Electro Discharge Milling for Microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2005)

Estimating Bankfull Discharge and Depth in Ungauged Estuaries
by: Gisen, J. I. A., et al.
Published: (2015)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Optimization of multi-holes drilling path using particle swarm optimization
by: Najwa Wahida, Zainal Abidin
Published: (2022)

Effect of surface roughness using different electrodes on electrical discharge machining
by: Mohd Abd Latif, Abd Ghani
Published: (2008)

Study on sediment size and discharge at Lebir River due to 2014 flood
by: Raja Irni Fatini, Raja Idnan
Published: (2016)