Prediction of burr formation in fabricating MEMS components by micro end milling

QR Code

Prediction of burr formation in fabricating MEMS components by micro end milling

This paper discusses burr formation in micromilling of AISI 304 stainless steel. Chip load, cutting speed and the application of coolant were chosen as the milling parameters. Experiments were conducted using 500 µm diameter tungsten carbide end milling tool. Milling parameters and measured burr hei...

Full description

Bibliographic Details
Main Authors:	Ali, Mohammad Yeakub, Omar, Mohd Aliff, Othman, Khairul Irman, Hung, Wayne N.P.
Format:	Article
Language:	English
Published:	Trans Tech Publications Ltd., Switzerland 2009
Subjects:	TJ Mechanical engineering and machinery
Online Access:	http://irep.iium.edu.my/1021/ http://irep.iium.edu.my/1021/1/Prediction_of_Burr_formation_in_fabricating_MEMs_components_by_micro_end_miling.pdf

Similar Items

Prediction of burr formation in fabricating MEMS components by micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Investigation of burr formation in micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Development of micro end milling process for fabricating MEMS
by: Ali, Mohammad Yeakub
Published: (2009)

Fabrication of three dimensional micro-components – A review
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Fabrication of micro cavities by micro electrical discharged machining
by: Ali, Mohammad Yeakub, et al.
Published: (2000)

Micro end milling of AISI 304 stainless steel and analysis of micro surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2009)

Fabrication of microfluidic channel using micro end milling and micro electrical discharge milling
by: Ali, Mohammad Yeakub
Published: (2009)

Effect of micro-milling parameters on burr formation and surface roughness in aluminum microchannels puncher
by: Mohd Saifuldin, Mohd Mokhtar, et al.
Published: (2024)

Elimination of burr formation during end milling of Polymethyl Methacrylate (PMMA) through high speed machining
by: Amin, A. K. M. Nurul, et al.
Published: (2011)

Chip pattern, burr and surface roughness in laser assisted micro milling of Ti6Al4V using micro ball end mill
by: Mohid, Z., et al.
Published: (2018)

Vibration issue in micro end milling
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Burr Reduction of Micro-milled Microfluidic Channels Mould Using a Tapered Tool
by: Saptaji, Kushendarsyah, et al.
Published: (2017)

Prediction of minimum chip thickness in tool based micro end milling
by: Ali, Mohammad Yeakub, et al.
Published: (2012)

Fabrication of micro dimples pattern using ball end mill
by: Muhamad Izdhar, Zaki, et al.
Published: (2019)

Effect of machining parameters on micro-burrs formation of aluminium puncher using high-speed machining process
by: Mohd Saifuldin, Mokhtar, et al.
Published: (2024)

Design and fabrication of micro swiss-roll combustor mold by micro EDM milling
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Surface roughness analysis of beryllium-copper alloy in micro end milling
by: Mehfuz, R., et al.
Published: (2007)

Empirical modelling of vibration in micro end milling of PMMA
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Investigation of burr in high speed microdrilling
by: Ali, Mohammad Yeakub, et al.
Published: (2013)

Influence of micro end milling process parameters on surface roughness
by: Ali, Mohammad Yeakub, et al.
Published: (2008)

Effect of micro end milling tool diameter on minimum chip thickness
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Tool vibration due to high speed micro end milling parameters
by: Mohamed, Abd. Rahman, et al.
Published: (2013)

Fabrication of Bio-MEMS Nanostructure by focused ion beam
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Using Finite Element simulation to investigate the effect of cutting edge radius on burr formation for inclined dimple milling operation
by: Mohd Ali Hanafiah, Shaharudin, et al.
Published: (2023)

Investigation of minimum chip thickness in micro end milling of PMMA: process development
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Virtual Laser-micromachining of MEMS Components
by: M. F. F., Ab Rashid, et al.
Published: (2009)

Performance of laser assisted micro-milling (laμmill) of titanium alloy using micro ball end mill
by: Mohid, Zazuli
Published: (2018)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Ahmed, Mirghani Ishag, et al.
Published: (2014)

Feasibility of double-layer microchannel fabrication at low speed micro end-mill and wire-cut EDM machines
by: Seder, Islam M.F., et al.
Published: (2014)

Prediction Modeling of Torque in End-milling
by: K., Kadirgama, et al.
Published: (2010)

Process capability of high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Mass-replication of micro-components
by: Ali, Mohammad Yeakub, et al.
Published: (2003)

Investigation of surface roughness and material removal rate for high speed micro end milling on PMMA
by: Rahman Azmil, Nur Atiqah, et al.
Published: (2015)

Micromachining
by: Ali, Mohammad Yeakub, et al.
Published: (2016)

Effects on vibration and surface roughness in high speed micro end-milling of Inconel 718 with minimum quantity lubrication
by: Abd. Rahman, Mohamed, et al.
Published: (2017)

Investigation of chip formation and minimum chip thickness in micro/meso milling: Methodology and design of experiment
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Prediction Modelling Of Power And Torque In End-Milling
by: K., Kadirgama, et al.
Published: (2009)

LNF Micro-Contact using MEMS and EFF Technology
by: Bhuiyan, Moinul, et al.
Published: (2013)

Investigation of minimum chip thickness in micro end milling of PMMA: Experiment and analysis 800 µm diameter tool
by: Mohammad , Yeakub Ali, et al.
Published: (2011)

Weibull Burr X distribution properties and application
by: Ibrahim, Noor Akma, et al.
Published: (2017)