A Review Paper on Machining of Metal Matrix Composite and Optimizing Methods used in Electrical Discharge Machining

QR Code

A Review Paper on Machining of Metal Matrix Composite and Optimizing Methods used in Electrical Discharge Machining

© 2018 Elsevier Ltd. Electric discharge machining is a non-conventional thermal erosion process. In this article investigation has been done on the effect of different reinforcement (carbides, oxides and nitrides), dielectric (kerosene, distilled water and PMEDM) and methods (RSM and GRA) for machin...

Full description

Bibliographic Details
Main Authors:	Paswan, K., Chattopadhyaya, S., Pramanik, Alokesh
Format:	Conference Paper
Published:	2018
Online Access:	http://hdl.handle.net/20.500.11937/73731

Similar Items

Effect of composition and grain structure on machining performance in EDM-A review
by: Paswan, K., et al.
Published: (2018)

Degradation of wire electrode during electrical discharge machining of metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2016)

Machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2009)

An FEM analysis of metal matrix composite machining
by: Pramanik, Alokesh, et al.
Published: (2006)

Machining of particulate-reinforced metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2008)

Developments in the non-traditional machining of particle reinforced metal matrix composites
by: Pramanik, Alokesh
Published: (2014)

Optimum Parameters for Machining Metal Matrix Composite
by: Boswell, Brian, et al.
Published: (2014)

Electrical Discharge Machining of MMCs Reinforced with Very Small Particles
by: Pramanik, Alokesh
Published: (2016)

Accuracy and finish during wire electric discharge machining of metal matrix composites for different reinforcement size and machining conditions
by: Pramanik, A., et al.
Published: (2016)

Prediction of cutting forces in machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2006)

Particle fracture and debonding during orthogonal machining of metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2017)

Tool wear and surface quality of metal matrix composites due to machining: A review
by: Hakami, F., et al.
Published: (2017)

Electrical discharge machining of 6061 aluminium alloy
by: Pramanik, Alokesh, et al.
Published: (2015)

Sustainability in wire electrical discharge machining of titanium alloy: Understanding wire rupture
by: Pramanik, Alokesh, et al.
Published: (2018)

Effect of machining parameters on deformation behaviour of Al-based metal matrix composites under tension
by: Pramanik, Alokesh, et al.
Published: (2018)

Review of machining metal matrix composites
by: Nicholls, C., et al.
Published: (2017)

Machine Parameter Optimization For Wire-Electric Discharge Machining
by: F. R. M., Romlay, et al.
Published: (2008)

Machining of metal matrix composites: effect of ceramic particles on residual stress, surface roughness and chip formation
by: Pramanik, Alokesh, et al.
Published: (2008)

Accuracy of duplex stainless steel feature generated by electrical discharge machining (EDM)
by: Alshemary, A., et al.
Published: (2018)

Effect of Size, Content and Shape of Reinforcements on the Behavior of Metal Matrix Composites (MMCs) Under Tension
by: Paknia, A., et al.
Published: (2016)

Processes and Characterizations of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2012)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Optimization of the electrical discharge machining performance on titanium alloy by using statistical method
by: Maizatul Asnida, Hassan
Published: (2013)

Fabrication of nano-particle reinforced metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2013)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Wire electrical discharge machining for microfabrication
by: Ali, Mohammad Yeakub, et al.
Published: (2007)

Dry electrical discharge machining: an environmental friendly machining process
by: Ali, Mohammad Yeakub
Published: (2018)

Optimization of machining parameters of titanium alloy in electric discharge machining based on artificial neural network
by: Liew, Annie Ann Nee
Published: (2010)

NON-CONVENTIONAL MACHINING OF ALUMINIUM METAL MATRIX COMPOSITE
by: Ahmad Majdi , Abdul Rani, et al.
Published: (2009)

Surface formation and modification in electrical discharge machining
by: Ahmed, Shamraze
Published: (2022)

Wire Electrical Discharge Machining of Tungsten Carbide
by: Mas Ayu, Hassan
Published: (2008)

Fatigue life of machined components
by: Pramanik, Alokesh, et al.
Published: (2017)

Failure Mechanisms of Nanoparticle Reinforced Metal Matrix Composite
by: Basak, A., et al.
Published: (2013)

Mechanism of Force Generation in Cutting Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2005)

Micro–indentation of metal matrix composites – an FEM investigation
by: Pramanik, Alokesh, et al.
Published: (2007)

Contribution of machining to the fatigue behaviour of metal matrix composites (MMCs) of varying reinforcement size
by: Pramanik, A., et al.
Published: (2017)

Residual stress generation in metal matrix composites after cooling
by: Wong, C., et al.
Published: (2018)

Performance enhancement of energy saving and machining characteristic in electrical discharge machining on magnesium alloy: A review
by: Norizwan, Juraimi, et al.
Published: (2020)

Problems and solutions in machining of titanium alloys
by: Pramanik, Alokesh
Published: (2014)

Effects of machining characteristics on electric discharge machine using different electrode materials
by: Mohd Khairul Anuar, Mohd Idris
Published: (2008)

Cannot write session to /tmp/vufind_sessions/sess_derjvjfm1e82nnhjgbnth716g5