Effect of composition and grain structure on machining performance in EDM-A review

QR Code

Effect of composition and grain structure on machining performance in EDM-A review

© Published under licence by IOP Publishing Ltd. Nowadays, MMC materials are in trend. EDM process fulfills the requirement of manufacturing product of MMC. MMC materials have a wide range of composition. The machinability of materials varies with the composition and grain size. The machining proper...

Full description

Bibliographic Details
Main Authors:	Paswan, K., Chattopadhyaya, S., Pramanik, Alokesh
Format:	Conference Paper
Published:	2018
Online Access:	http://hdl.handle.net/20.500.11937/69832

Similar Items

A Review Paper on Machining of Metal Matrix Composite and Optimizing Methods used in Electrical Discharge Machining
by: Paswan, K., et al.
Published: (2018)

Accuracy of duplex stainless steel feature generated by electrical discharge machining (EDM)
by: Alshemary, A., et al.
Published: (2018)

Effect of reinforced particle size on wire EDM of MMCs
by: Pramanik, Alokesh, et al.
Published: (2015)

Wire EDM Mechanism of MMCs with the Variation of Reinforced Particle Size
by: Pramanik, Alokesh, et al.
Published: (2016)

Effect of Size, Content and Shape of Reinforcements on the Behavior of Metal Matrix Composites (MMCs) Under Tension
by: Paknia, A., et al.
Published: (2016)

Machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2009)

Electrical discharge machining (EDM): A review
by: Banu, Asfana, et al.
Published: (2016)

Developments in the non-traditional machining of particle reinforced metal matrix composites
by: Pramanik, Alokesh
Published: (2014)

Tool wear and surface quality of metal matrix composites due to machining: A review
by: Hakami, F., et al.
Published: (2017)

Influence of Nano-particle on the Wear behaviour of Thin Film Coatings: A Review
by: Chattopadhyaya, S., et al.
Published: (2018)

Effect of machining parameters on deformation behaviour of Al-based metal matrix composites under tension
by: Pramanik, Alokesh, et al.
Published: (2018)

Wear behavior of chromium nitride coating in dry condition at lower sliding velocity and load
by: Singh, S., et al.
Published: (2018)

Particle fracture and debonding during orthogonal machining of metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2017)

An FEM analysis of metal matrix composite machining
by: Pramanik, Alokesh, et al.
Published: (2006)

Machining of particulate-reinforced metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2008)

Degradation of wire electrode during electrical discharge machining of metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2016)

Fatigue life of machined components
by: Pramanik, Alokesh, et al.
Published: (2017)

Effect of powder concentration on EDM performance during machining mild steel
by: Khan, Ahsan Ali, et al.
Published: (2015)

Prediction of cutting forces in machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2006)

Problems and solutions in machining of titanium alloys
by: Pramanik, Alokesh
Published: (2014)

Optimum Parameters for Machining Metal Matrix Composite
by: Boswell, Brian, et al.
Published: (2014)

Performance Analysis of Pulsating Water Jet Machining During Disintegration of Rocks by Means of Acoustic Emission
by: Tripathi, R., et al.
Published: (2018)

Effects of reinforcement on wear resistance of aluminum matrix composites
by: Pramanik, Alokesh
Published: (2016)

Machining of metal matrix composites: effect of ceramic particles on residual stress, surface roughness and chip formation
by: Pramanik, Alokesh, et al.
Published: (2008)

ELID grinding and EDM for finish machining
by: Saleh, Tanveer, et al.
Published: (2017)

An introduction to electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2011)

Mechanisms and Performance of Composite Joints Through Adhesive and Interlocking Means—A Review
by: Davaasambuu, Khishigdorj, et al.
Published: (2025)

Electrical Discharge Machining of MMCs Reinforced with Very Small Particles
by: Pramanik, Alokesh
Published: (2016)

Performance of electrical discharge machining (EDM) with nickel added dielectric fluid
by: Khan, Ahsan Ali, et al.
Published: (2018)

Effect of Machining on the Fatigue Life of Steels
by: Hakami, F., et al.
Published: (2016)

Magnetic polarity influence on machining performance of magnetic field-assisted edm
by: Mohd Efendee, Awang
Published: (2020)

Processing of duplex stainless steel by WEDM
by: Pramanik, Alokesh, et al.
Published: (2018)

Characterization of ceramic materials after machining by EDM
by: Maleque, Md. Abdul
Published: (2012)

Improving machining performance using alumina powder-added dielectric during electrical discharge machining (EDM)
by: Khan, Ahsan Ali, et al.
Published: (2017)

Effects of workpiece composition and depth-of-cut during ultra-precision machining of electroless-nickel
by: Pramanik, Alokesh, et al.
Published: (2007)

Relationship between electrode size and machined surface in the EDM machining process
by: Mohd Azrul Aminur, Ismail
Published: (2008)

Ultra-precision Machinability and Properties of Electroless-nickel
by: Pramanik, Alokesh, et al.
Published: (2013)

Effects of electrical discharge machining (EDM) jet flushing setting on the machining of tool steel workpiece
by: Hasan, Muda
Published: (2009)

Effects of polarity parameter on the machining of tool steel workpiece using electric discharge machining (EDM)
by: Ahmad Fadzil, Mohamad
Published: (2009)

Minimizing wear of EDM electrode in machining a hard material
by: Muhammad Qahri Harir, Mohd Rapi
Published: (2017)