Optimizing Power Consumption for Sustainable Dry Turning of Treated Aluminum Alloy

QR Code

Optimizing Power Consumption for Sustainable Dry Turning of Treated Aluminum Alloy

© 2015 The Authors Machining companies can implement sustainable manufacturing using steps to improving the performance of economic, environmental and social. One of the steps is to perform the efficiency of energy consumption (mainly electricity) in machining. This paper describes a case study whic...

Full description

Bibliographic Details
Main Authors:	Nur, R., Kurniawan, Denni, Noordin, M., Izman, S.
Format:	Journal Article
Published:	2015
Online Access:	http://hdl.handle.net/20.500.11937/67494

Similar Items

Power demand calculations in turning of aluminum alloy
by: Nur, R., et al.
Published: (2014)

The effect of cutting parameters on power consumption during turning nickel based alloy
by: Nur, R., et al.
Published: (2014)

Machining parameters effect in dry turning of AISI 316L stainless steel using coated carbide tools
by: Nur, R., et al.
Published: (2017)

Sustainable optimization of dry turning of stainless steel based on energy consumption and machining cost
by: Bagaber, Salem Abdullah, et al.
Published: (2018)

Multi-Objective Optimization of Cutting Parameters to Minimize Power Consumption in Dry Turning of Stainless Steel 316
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Effect of Coolant Nozzle Sizes on Turning Aluminum Alloy AL319
by: Zainal Ariffin, Selamat, et al.
Published: (2016)

Vortex Tube Air Cooling: The Effect on Surface Roughness and Power Consumption in Dry Turning
by: Zahari, Taha, et al.
Published: (2013)

Effect of cutting parameters on surface roughness in turning of bone
by: Ndaruhadi, P., et al.
Published: (2014)

Effect of heat treatment on microstructure homogeneity of Zn-3Mg alloy
by: Dambatta, M., et al.
Published: (2014)

Power Consumption Optimization in CNC Turning Process Using Multi Objective Genetic Algorithm
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2012)

Influence of heat treatment cooling mediums on the degradation property of biodegradable Zn-3Mg alloy
by: Dambatta, M., et al.
Published: (2014)

Processing of Zn-3Mg alloy by equal channel angular pressing for biodegradable metal implants
by: Dambatta, M., et al.
Published: (2017)

Effect of high speed dry end milling on surface roughness and cutting forces of Ti-6Al-4V ELI
by: Sharif, S., et al.
Published: (2014)

Machining of bone: Analysis of cutting force and surface roughness by turning process
by: Noordin, M., et al.
Published: (2015)

Feasibility of mild hard turning of stainless steel using coated carbide tool
by: Noordin, M., et al.
Published: (2012)

Dry machining and minimum quantity lubricant of aluminum alloy 6061-t6 using coated carbide tools
by: Nur Amirra, Rashid
Published: (2013)

Tool Life of Coated Carbide Cutting Tool when Turning Hardened Stainless Steel under Minimum Quantity Lubricant Using Castor Oil
by: Elmunafi, M., et al.
Published: (2015)

Hard turning of cold work tool steel using wipper ceramic tool
by: Mohd. Yusof, Noordin, et al.
Published: (2008)

Tribological (wear) properties of aluminum–silicon eutectic base alloy under dry sliding condition
by: Alias, Tuti Yasmin, et al.
Published: (2004)

Analysis of surface integrity and formation of material side flow in dry and wet machining of aluminum alloy
by: A. B., Hadzley, et al.
Published: (2018)

Effect of cutting parameters on the hole diameter and surface roughness for dry drilling of aluminum alloy 6061
by: Ahamed, Ahmad Fauzi
Published: (2010)

Comparison of dry and cryogenic machining on chip formation and coefficient of friction in turning AISI 4340 alloy steel
by: A. Raof, Natasha, et al.
Published: (2014)

Influence of thermal treatment on microstructure, mechanical and degradation properties of Zn-3Mg alloy as potential biodegradable implant material
by: Dambatta, M., et al.
Published: (2015)

In vitro degradation and cell viability assessment of Zn-3Mg alloy for biodegradable bone implants
by: Dambatta, M., et al.
Published: (2015)

Effect of butt joint on mechanical properties of welded low carbon steel
by: Wardoyo, T., et al.
Published: (2014)

Effect of process parameters on quality of cold spinned tube head
by: Wardoyo, T., et al.
Published: (2013)

To study the effect of variable loading on fatigue properties of heat treated aluminum alloy 6063-T5 / William Lenjau
by: Lenjau, William
Published: (2003)

Surface morphology study on aluminum alloy after treated with silicate-based corrosion inhibitor from paddy residue
by: Mohamad, N., et al.
Published: (2014)

Effect of carburizing and annealing processes in improving the Ni/WC–Co adhesion strength
by: Hassan, A., et al.
Published: (2018)

Acid pretreatment of WC-Co for surface roughening and cobalt removal prior to CVD diamond coating
by: Norafifah, H., et al.
Published: (2013)

Quantitative analysis of electroplated nickel coating on hard metal
by: Wahab, H., et al.
Published: (2013)

Influence of Microwave and Conventional Annealing Processes in Improving an Electrodeposited Nickel Interlayer Characteristics
by: Hassan, A., et al.
Published: (2016)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Mechanical properties of sintered aluminum alloy compacts
by: Hrairi, Meftah, et al.
Published: (2011)

Fatigue damage characterization of aluminum alloy plates
by: Hrairi, Meftah, et al.
Published: (2011)

Optimization of cutting parameters and surface roughness on dry turning of low carbon steel
by: Hou, Lo Wei
Published: (2012)

Effect of rare earth addition on microstructure and mechanical properties of Al-Si alloys: An overview
by: Joy-Yii, S., et al.
Published: (2014)

Surface roughness IN high speed turning OF alloy steel m303 using carbide tools in dry cutting condition
by: Tahrin Othman,, et al.
Published: (2022)

Development Of Fuzzy Logic Model For Turning Process Of Steel Alloy And Titanium Alloys
by: Tan, Jit Yean
Published: (2004)

Aluminum Deoxidation Equilibrium in Molten Fe–Co Alloys
by: Gamutan, Jonah, et al.
Published: (2022)