Examining the effect of various vegetable oil-based cutting fluids on surface integrity in drilling steel - a review

QR Code

Examining the effect of various vegetable oil-based cutting fluids on surface integrity in drilling steel - a review

Increased attention on environmental and health impacts by industrial activities forces the manufacturing industry to reduce the mineral oil-based metalworking fluids as a cutting fluid. The advantages of using vegetable oil-based cutting fluids on tool wear and the cutting force have been reported...

Full description

Bibliographic Details
Main Authors:	Sultan, A., Sharif, S., Kurniawan, Denni
Format:	Conference Paper
Published:	2014
Online Access:	http://hdl.handle.net/20.500.11937/66853

Similar Items

Chip Formation When Drilling AISI 316L Stainless Steel using Carbide Twist Drill
by: Sultan, A., et al.
Published: (2015)

Effect of Different Cutting Speed and Feed Rate on Surface Roughness in Femur Bone Drilling
by: Ndaruhadi, P., et al.
Published: (2015)

Effect of Machining Parameters on Tool Wear and Hole Quality of AISI 316L Stainless Steel in Conventional Drilling
by: Sultan, A., et al.
Published: (2015)

Use of castor oil as cutting fluid in machining of hardened stainless steel with minimum quantity of lubricant
by: Elmunafi, M., et al.
Published: (2015)

Use of Castor Oil as Cutting Fluid in Machining of Hardened Stainless Steel with Minimum Quantity of Lubricant
by: Elmunafi, M., et al.
Published: (2015)

Study of cutting force and surface roughness on drilling stainless steel 316L under various coolant condition
by: Kamdani, K., et al.
Published: (2018)

Experiment investigation of hole accuracy and surface roughness in femur bone drilling using different parameters
by: Ndaruhadi, P., et al.
Published: (2014)

Effect of cutting parameters on surface roughness in turning of bone
by: Ndaruhadi, P., et al.
Published: (2014)

Laminate orientation effect on drilling of carbon fiber reinforced plastic composites
by: Hakimi, I., et al.
Published: (2013)

Effect of cutting speed and feed in turning hardened stainless steel using coated carbide cutting tool under minimum quantity lubrication using castor oil
by: Elmunafi, M., et al.
Published: (2015)

Surface integrity of titanium when machining with various cutting parameter
by: Mohd 'Azim, Ab. Halim
Published: (2010)

Effect of high speed dry end milling on surface roughness and cutting forces of Ti-6Al-4V ELI
by: Sharif, S., et al.
Published: (2014)

Effect of drill point angle on surface integrity when drilling titanium alloy
by: Murad, Muhamad Nasir, et al.
Published: (2014)

Microwave processing of oil contaminated drill cuttings
by: Pereira, Igor S. M.
Published: (2013)

Tool Life of Coated Carbide Cutting Tool when Turning Hardened Stainless Steel under Minimum Quantity Lubricant Using Castor Oil
by: Elmunafi, M., et al.
Published: (2015)

Bioremediation of drill cuttings from oil based muds
by: Turner, Katharine Patricia
Published: (2002)

Effect of cutting speed and depth of cut on surface roughness of oil-quench mild steel
by: Yeong, Choy Huey
Published: (2009)

Effect of cutting parameters on surface roughness in dry drilling of AISI D2 tool steel by using Taguchi Method
by: M.H. Osman1, M.H. Osman1, et al.
Published: (2018)

Cutting force and surface roughness characterization in cryogenic high-speed end milling of Ti-6Al-4V ELI
by: Safari, H., et al.
Published: (2014)

Effect of cutting parameters on the surface integrity of ground AISI 1148 steel
by: Ismail, Mohd. Rozaimi
Published: (2010)

Effect of cutting speed on Bio-corrosion of AISI 316L stainless steel
by: Saliza Azlina, O., et al.
Published: (2016)

Machining of bone: Analysis of cutting force and surface roughness by turning process
by: Noordin, M., et al.
Published: (2015)

Effect of vegetable and mineral oil-in-water emulsion cutting fluids in turning AISI 4340 steel with coated carbide tools / Sunday Albert Lawal
by: Sunday, Albert Lawal
Published: (2013)

Experimental analysis of tool wear when drilling carbon fibre composite (CFC) without cutting fluid, with cutting fluid and with a pre-cryogenically cooled tool
by: Dahnel, Aishah Najiah, et al.
Published: (2013)

Effect of nanoparticles in drilling fluids on the transportation of different cutting sizes in a rotating horizontal pipe
by: Oseh, Jeffrey O., et al.
Published: (2024)

Microwave treatment of oil contaminated drill cuttings produced on offshore oil platforms
by: Ogunniran, Oluwatosin
Published: (2017)

Palm oil diesel as a base fluid in formulating oil based drilling fluid
by: Md. Yassin, Abu Azam, et al.
Published: (1991)

Drilling cutting removal in inclined anuli - A review
by: Md. Yassin, Abu Azam
Published: (1987)

Improvement in the transport capacity of drilled particles of aqueous-based drilling fluid using surface-enriched hydroxyapatite nanoparticles
by: Oseh, Jeffrey O., et al.
Published: (2024)

An experimental investigation on drilling of aluminum alloy (Al 7075) using high speed steel cutting tools
by: Abd Halim, Nor Farah Huda, et al.
Published: (2020)

Effect Of Vegetable Oil On Surface Roughness During Turning Of Aisi 1020 Steel
by: Hing, Chen Teng
Published: (2021)

Study on the Rheology of Drilling Fluid and Its Impact on Drilling Operation
by: Wang, Yiwen
Published: (2019)

Biodiesel from various vegetables and tallow oils
by: Atiqah, Nafsun
Published: (2012)

Production of synthetic based drilling fluid from palm oil
by: Abdul Habib, Nor Saiful Hafiz
Published: (2013)

Drilling fluids based on a derivative of Malaysian palm oil
by: Samsuri, Ariffin, et al.
Published: (1993)

Effect of cutting parameters on the hole diameter and surface roughness for dry drilling of aluminum alloy 6061
by: Ahamed, Ahmad Fauzi
Published: (2010)

Analysis of deep hole drilling in presence of electromagnetic field using Taguchi technique
by: Najarian, F., et al.
Published: (2014)

Cuttings transportation in coiled tubing drilling for mineral exploration
by: Kamyab, Mohammadreza
Published: (2014)

Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2011)

Preliminary Study of Jatropha Curcas Oil as Ester-Based Drilling Fluids
by: Sonny Irawan, Sonny, et al.
Published: (2010)

Cannot write session to /tmp/vufind_sessions/sess_8qmfo3tqq4bmcgq8ae2k55fire