Performance Analysis of Pulsating Water Jet Machining During Disintegration of Rocks by Means of Acoustic Emission

QR Code

Performance Analysis of Pulsating Water Jet Machining During Disintegration of Rocks by Means of Acoustic Emission

Over the decades, water jet cutting has been widely used for rock disintegration in mining operations and quarrying purposes. The impact of high-pressure water jet on hard material like rock, coal ruins the original structure of the material; therefore, low-pressure water jet comes into the existenc...

Full description

Bibliographic Details
Main Authors:	Tripathi, R., Srivastava, M., Hloch, S., Chattopadhyaya, S., Das, A., Pramanik, Alokesh, Klichová, D., Adamcik, P.
Format:	Conference Paper
Published:	2018
Online Access:	http://hdl.handle.net/20.500.11937/61263

Similar Items

Surface topography analysis of mg-based composites with different nanoparticle contents disintegrated using abrasive water jet
by: Mardi, K.B., et al.
Published: (2021)

A Review Paper on Machining of Metal Matrix Composite and Optimizing Methods used in Electrical Discharge Machining
by: Paswan, K., et al.
Published: (2018)

Heat transfer enhancement in microchannels with cross-flow pulsating fluid jets
by: Chandratilleke, Tilak, et al.
Published: (2008)

Effect of composition and grain structure on machining performance in EDM-A review
by: Paswan, K., et al.
Published: (2018)

Disintegration
by: Farren, Beverley
Published: (2013)

Single phase and boiling heat transfer under steady and pulsating confined jet impingement
by: Sridhar, Abishek
Published: (2013)

Experimental Study of Low Frequency Pulsating Liquid Jet Impingement in a confined planar geometry
by: Sridhar, Abishek, et al.
Published: (2013)

Energy Redistribution between the Mean and Pulsating Flow Field in a Separated Flow Region
by: Dol, Sharul Sham, et al.
Published: (2014)

Effects of pulsation to the mean field and vortex development in a backward-facing step flow
by: Dol, Sharul Sham, et al.
Published: (2014)

Prickly Pear Disintegration
by: Kinsella, John
Published: (2017)

Wear behavior of chromium nitride coating in dry condition at lower sliding velocity and load
by: Singh, S., et al.
Published: (2018)

Shear failure mechanism and acoustic emission characteristics of jointed rock-like specimens
by: Ban, Yuxin, et al.
Published: (2021)

Fatigue life of machined components
by: Pramanik, Alokesh, et al.
Published: (2017)

Machining surface roughness monitoring using acoustic emission method
by: Mohd Syazlan, Mohd Hatta
Published: (2010)

Pulsation-assisted fluidised bed drying of heat-sensitive and sticky materials: effect of basic parameter, and pulsation-specific parameter
by: Luqman, Abdul Halim, et al.
Published: (2022)

Problems and solutions in machining of titanium alloys
by: Pramanik, Alokesh
Published: (2014)

Broadband pulsations from PSR B1821-24: Implications for emission models and the pulsar population of M28
by: Johnson, T., et al.
Published: (2013)

Development of acoustic emission diagnostic system for condition monitoring of rotating machines
by: N., Saad, et al.
Published: (2008)

Analysis of acoustic emission during abrasive waterjet machining of sheet metals
by: Nazrin, Mokhtar, et al.
Published: (2018)

Electrical Discharge Machining of MMCs Reinforced with Very Small Particles
by: Pramanik, Alokesh
Published: (2016)

Developments in the non-traditional machining of particle reinforced metal matrix composites
by: Pramanik, Alokesh
Published: (2014)

Pulsating fronts in periodically modulated neural field models
by: Coombes, Stephen, et al.
Published: (2011)

Improved Drying in a Pulsation-Assisted Fluidized Bed
by: Akhavan, A., et al.
Published: (2009)

A novel flow control valve for pulsating flows
by: Chaugule, V., et al.
Published: (2014)

Surface integrity of Mg-based nanocomposite produced by Abrasive Water Jet Machining (AWJM)
by: Mardi, K., et al.
Published: (2017)

Machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2009)

A study of acoustic emission technique on incipient detection of rotating machine faults
by: N., Saad, et al.
Published: (2008)

Monitoring tool wear process in turning machine using acoustic emission technique
by: Azlan, Mohd Saini
Published: (2010)

Processing of duplex stainless steel by WEDM
by: Pramanik, Alokesh, et al.
Published: (2018)

Influence of Nano-particle on the Wear behaviour of Thin Film Coatings: A Review
by: Chattopadhyaya, S., et al.
Published: (2018)

Effect of Size, Content and Shape of Reinforcements on the Behavior of Metal Matrix Composites (MMCs) Under Tension
by: Paknia, A., et al.
Published: (2016)

Evaluation of Orifice Flow Meter Accuracy under Pulsation Conditions
by: Abdullah, mohammad, et al.
Published: (2015)

Orifice plate flowmeter performance under pulsating flow conditions
by: Idres, Moumen, et al.
Published: (2014)

Dynamic Response of Silo Supporting Structure under Pulsating Loads
by: Tu, Phung
Published: (2017)

Ultra-precision Machinability and Properties of Electroless-nickel
by: Pramanik, Alokesh, et al.
Published: (2013)

On-line fault detection & diagnosis of rotating machines using acoustic emission monitoring techniques
by: M.A.A., Elmaleeh, et al.
Published: (2007)

Acoustic Emission and Artificial Intelligent Methods in Condition Monitoring of Rotating Machine – A Review
by: Yasir , Hassan Ali, et al.
Published: (2016)

Comparison of disintegrant-addition methods on the compounding of orodispersible tablets
by: Mahesparan, Vishnu, et al.
Published: (2020)

Effect of acoustic excitation toward jet flame: an experimental design
by: Sapit, Azwan, et al.
Published: (2019)

Fracture and fatigue life of Al-based MMCs machined at different conditions
by: Pramanik, Alokesh, et al.
Published: (2018)

Cannot write session to /tmp/vufind_sessions/sess_trbkdl5j01a0dsud0gshqsmtl9