Effect of Size, Content and Shape of Reinforcements on the Behavior of Metal Matrix Composites (MMCs) Under Tension

QR Code

Effect of Size, Content and Shape of Reinforcements on the Behavior of Metal Matrix Composites (MMCs) Under Tension

The objective of this research was to investigate the mechanical behavior of metal matrix composites (MMCs) 6061 aluminum, reinforced with silicon carbide particles, under unidirectional tensile loading by finite element analysis. The effects of particle’s shape, size and content on the tensile prop...

Full description

Bibliographic Details
Main Authors:	Paknia, A., Pramanik, Alokesh, Dixit, A., Chattopadhyaya, S.
Format:	Journal Article
Published:	Springer 2016
Online Access:	http://hdl.handle.net/20.500.11937/52925

Similar Items

Contribution of machining to the fatigue behaviour of metal matrix composites (MMCs) of varying reinforcement size
by: Pramanik, A., et al.
Published: (2017)

Effect of reinforced particle size on wire EDM of MMCs
by: Pramanik, Alokesh, et al.
Published: (2015)

Wire EDM Mechanism of MMCs with the Variation of Reinforced Particle Size
by: Pramanik, Alokesh, et al.
Published: (2016)

Electrical Discharge Machining of MMCs Reinforced with Very Small Particles
by: Pramanik, Alokesh
Published: (2016)

An experimental study on machining of SiC reinforced MMCs
by: Pramanik, Alokesh, et al.
Published: (2006)

Deformation mechanisms of MMCs under indentation
by: Pramanik, Alokesh, et al.
Published: (2008)

Effect of machining parameters on deformation behaviour of Al-based metal matrix composites under tension
by: Pramanik, Alokesh, et al.
Published: (2018)

Fracture and fatigue life of Al-based MMCs machined at different conditions
by: Pramanik, Alokesh, et al.
Published: (2018)

A Review Paper on Machining of Metal Matrix Composite and Optimizing Methods used in Electrical Discharge Machining
by: Paswan, K., et al.
Published: (2018)

Developments in the non-traditional machining of particle reinforced metal matrix composites
by: Pramanik, Alokesh
Published: (2014)

Fabrication of nano-particle reinforced metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2013)

Machining of particulate-reinforced metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2008)

Failure Mechanisms of Nanoparticle Reinforced Metal Matrix Composite
by: Basak, A., et al.
Published: (2013)

Tribological behavior of dual and triple particle size SiC reinforced Al-MMCs: a comparative study
by: Maleque, Md Abdul, et al.
Published: (2008)

Tribological behavior of dual and triple particle size SiC reinforced Al0MMCs: a comparative study
by: Maleque, Md. Abdul, et al.
Published: (2008)

Processing of duplex stainless steel by WEDM
by: Pramanik, Alokesh, et al.
Published: (2018)

Milling of Nanoparticles Reinforced Al-Based Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2018)

Challenges and recent developments on nanoparticle-reinforced metal matrix composites
by: Basak, A., et al.
Published: (2015)

Challenges and recent developments on nano-particle reinforced metal matrix composite
by: Basak, A., et al.
Published: (2015)

Effects of reinforcement on wear resistance of aluminum matrix composites
by: Pramanik, Alokesh
Published: (2016)

Machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2009)

Processes and Characterizations of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2012)

Wear behavior of chromium nitride coating in dry condition at lower sliding velocity and load
by: Singh, S., et al.
Published: (2018)

Degradation of wire electrode during electrical discharge machining of metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2016)

Residual stress generation in metal matrix composites after cooling
by: Wong, C., et al.
Published: (2018)

Micro–indentation of metal matrix composites – an FEM investigation
by: Pramanik, Alokesh, et al.
Published: (2007)

An FEM analysis of metal matrix composite machining
by: Pramanik, Alokesh, et al.
Published: (2006)

Particle fracture and debonding during orthogonal machining of metal matrix composites
by: Pramanik, Alokesh, et al.
Published: (2017)

Prediction of cutting forces in machining of Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2006)

Optimum Parameters for Machining Metal Matrix Composite
by: Boswell, Brian, et al.
Published: (2014)

Accuracy and finish during wire electric discharge machining of metal matrix composites for different reinforcement size and machining conditions
by: Pramanik, A., et al.
Published: (2016)

Mechanism of Force Generation in Cutting Metal Matrix Composites
by: Pramanik, Alokesh, et al.
Published: (2005)

Tool wear and surface quality of metal matrix composites due to machining: A review
by: Hakami, F., et al.
Published: (2017)

Performance of the reinforced concrete beam with arch shaped tension steel bar
by: Mangaibagan, Rajandran
Published: (2016)

Wear behavior of as-cast and heat treated triple particle size SiC reinforced aluminium metal matrix composites
by: Maleque, Md. Abdul, et al.
Published: (2009)

Micro-indentation of metal matrix composites: a 3D finite element analysis
by: Pramanik, Alokesh, et al.
Published: (2012)

Muslim ummah, international organisations, and human development in the MMCs
by: Hossain, Ishtiaq
Published: (2012)

An FEM investigation into the behaviour of metal matrix composites: tool–particle interaction during orthogonal cutting
by: Pramanik, Alokesh, et al.
Published: (2007)

Mechanical properties and behaviour of concrete reinforced with spiral-shaped steel fibres under dynamic splitting tension
by: Hao, Y., et al.
Published: (2016)

Effect of composition and grain structure on machining performance in EDM-A review
by: Paswan, K., et al.
Published: (2018)