Effects of insert geometry and feed rate on quality characteristics of turned parts

QR Code

Effects of insert geometry and feed rate on quality characteristics of turned parts

This paper investigates experimentally and analytically the influence of insert geometry and feed rate on the quality characteristics of turned parts under the dry cutting condition. A three-level, three-parameter experiment was planned using the design of experiment methodology. The three levels of...

Full description

Bibliographic Details
Main Authors:	Islam, Mohammad Nazrul, Pramanik, Alokesh
Format:	Journal Article
Published:	2015
Online Access:	http://hdl.handle.net/20.500.11937/48962

Similar Items

Effect of tool geometry on dimensional accuracy and surface finish of turned parts
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2011)

Off-Line Feed Rate Scheduling Based on a Mechanistic Cutting Force on Discrete Segments during End Milling
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Effect of Additional Factors on Dimensional Accuracy and Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2013)

Comparison of Dry and Flood Turning in Terms of Dimensional Accuracy and Surface Finish of Turned Parts
by: Rafai, Noor, et al.
Published: (2011)

Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

An Investigation of Dimensional Accuracy of Parts Produced by Three-Dimensional Printing
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Quantifying quality of learning during teaching an undergraduate unit: Manufacturing processes
by: Pramanik, Alokesh, et al.
Published: (2015)

Ductile mode turning of brittle materials and its practical aspects
by: Pramanik, Alokesh, et al.
Published: (2013)

Technology tools and approaches to improve undergraduate education
by: Pramanik, Alokesh, et al.
Published: (2015)

Introduction of a new software package in teaching Design Methodology for material selection
by: Pramanik, Alokesh, et al.
Published: (2015)

Comparison of Design of Experiments via Traditional and Taguchi Method
by: Islam, Mohammad Nazrul, et al.
Published: (2016)

Module-based teaching of mechanical design
by: Pramanik, Alokesh, et al.
Published: (2014)

Experimental Investigation of the Effect of Feed Rate and Negative Tool Rake Angle in High Speed Hard Turning
by: Al Hazza, Muataz Hazza Faizi, et al.
Published: (2013)

Effect of reinforced particle size on wire EDM of MMCs
by: Pramanik, Alokesh, et al.
Published: (2015)

Stagnation zone during the turning of Duplex SAF 2205 stainless steels alloy
by: Nomani, J., et al.
Published: (2017)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Pineapple waste turned into drone parts
by: Harris, Ebrahim
Published: (2021)

Investigation on the Behavior of Austenite and Ferrite Phases at Stagnation Region in the Turning of Duplex Stainless Steel Alloys
by: Nomani, J., et al.
Published: (2016)

Investigation On The Effect Of Dry Turning On AISI 305 Steel With Ceramic Inserts By Analysis Of Workpiece Surface Profile
by: Mohamad, Nurnadia Azwa
Published: (2018)

Effect Of Tool Geometry And Nose Profile Micro-Deviation On Surface Roughness In Finish Turning
by: Sung , Aun Naa
Published: (2015)

Ultra–Precision Turning of Electroless–Nickel: Effects of crystal orientation and origin of diamond tools
by: Pramanik, Alokesh, et al.
Published: (2009)

Ultra–Precision Turning of Electroless–Nickel: Effect of Phosphorus Contents, Depth–of–cut and Rake Angle
by: Pramanik, Alokesh, et al.
Published: (2008)

Failure Mechanisms of Nanoparticle Reinforced Metal Matrix Composite
by: Basak, A., et al.
Published: (2013)

Optimum Parameters for Machining Metal Matrix Composite
by: Boswell, Brian, et al.
Published: (2014)

Dimensional Accuracy Achievable by Three-Dimensional Printing
by: Islam, Mohammad Nazrul, et al.
Published: (2014)

Sustainable Machining of Aerospace Material
by: Boswell, Brian, et al.
Published: (2013)

Optimization of tool geometry design for free cutting steel (AISI 12L14) in turning operation
by: Mohammad, Rosdi
Published: (2017)

Analysis of Dry Turning Process of AISI316 for Coated and Uncoated Insert Tools Based on Economical Method
by: Bagaber, Salem Abdullah, et al.
Published: (2016)

A comparative study on performance of CBN inserts when turning steel under dry and wet conditions
by: Bagaber, Salem Abdullah, et al.
Published: (2017)

Performance evaluation of alumina-graphene hybrid nano-cutting fluid in hard turning
by: Singh, R., et al.
Published: (2017)

Effect of feed channel spacer geometry on hydrodynamics and mass transport in membrane modules
by: Saeed, Asim
Published: (2012)

Assessment of the ease of insertion, retention rate, ease of removal and pig behaviour to a novel intravaginal insert for pigs
by: Jong, Kwang Yan
Published: (2016)

Effects of reinforcement on wear resistance of aluminum matrix composites
by: Pramanik, Alokesh
Published: (2016)

Cutting performance of diamond tools during ultra–precision turning of electroless nickel plated die materials
by: Pramanik, Alokesh, et al.
Published: (2003)

Effect of drying parameters and geometry on papaya quality
by: Md. Zaki, Nurul Asyikin, et al.
Published: (2005)

Wave Impacts on Structures with Rectangular Geometries: Part 1. Seawalls
by: Nor Aida Zuraimi, Md Noar, et al.
Published: (2015)

The Effect of the Thermal Behaviour of a Machine Tool on the Dimensional Accuracy of Parts
by: Lu, Yuxia, et al.
Published: (2011)

Tool wear and surface finish investigation in high speed turning using cermet insert by applying negative rake angles
by: Adesta, Erry Yulian Triblas, et al.
Published: (2009)