Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts

QR Code

Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts

This paper presents the experimental and analytical results of different cutting fluid supply strategies—dry, minimum quantity lubrication (MQL) and flood turning in terms of the surface finish of turned parts. Subsequently, the influence of independent input parameters on surface finish is investig...

Full description

Bibliographic Details
Main Authors:	Islam, Mohammad Nazrul, Rafai, Noor, Heng, Boon
Format:	Journal Article
Published:	Trans Tech Publications Ltd. 2011
Subjects:	Taguchi methods dry turning Pareto ANOVA analysis flood turning minimum quantity lubrication (MQL)
Online Access:	http://hdl.handle.net/20.500.11937/38129

Similar Items

Effect of Additional Factors on Dimensional Accuracy and Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2013)

Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2011)

Comparison of Dry and Flood Turning in Terms of Dimensional Accuracy and Surface Finish of Turned Parts
by: Rafai, Noor, et al.
Published: (2011)

Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Effect of tool geometry on dimensional accuracy and surface finish of turned parts
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Dimensional Accuracy Achievable in Wire-cut Electrical Discharge Machining
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Reduction of amount of cutting fluid in flood turning by finite element analysis
by: Islam, Mohammad Nazrul, et al.
Published: (2012)

Development of Machine Learning Algorithm for Acquiring Machining Data in Turning Process
by: Ali Al-Assadi, Hayder M. A.
Published: (2004)

Cutting performance of diamond tools during ultra–precision turning of electroless nickel plated die materials
by: Pramanik, Alokesh, et al.
Published: (2003)

Unfinished Turns in French: How Context Matters
by: Chevalier, Fabienne HG
Published: (2008)

Ductile mode turning of brittle materials and its practical aspects
by: Pramanik, Alokesh, et al.
Published: (2013)

Their Dreams and Ours: Britten, Film, and 'The Turn of the Screw'
by: Auker, Peter Leslie Roy
Published: (2021)

Feasibility Study of Adopting Minimal Quantities of Lubrication for End Milling Aluminium
by: Boswell, Brian, et al.
Published: (2012)

An Experimental Approach to Determine the Effectiveness of Minimum Liquid Cooling for End Milling 1040 Steel
by: Boswell, Brian
Published: (2010)

Environmental friendly cutting fluids and cooling techniques in machining: a review
by: Debnath, Sujan, et al.
Published: (2014)

The impact of impulsive voltage waveforms on the electrical insulation of actuators for more electrical aircraft (MEA)
by: Cavallini, Andrea, et al.
Published: (2017)

Turn-turn short circuit fault management in permanent magnet machines
by: Arumugam, Puvaneswaran, et al.
Published: (2015)

Ultra-precision machining of electroless nickel plated die materials
by: Pramanik, Alokesh, et al.
Published: (2002)

The Effect of Combined Cold Air and Minimum Liquid Cooling on End Milling
by: Boswell, Brian, et al.
Published: (2011)

The challenge of adopting minimal quantities of lubrication for end milling aluminium
by: Boswell, Brian, et al.
Published: (2013)

Non-linear circuit based model of PMSM under inter-turn fault: a simple approach based on healthy machine data
by: Belguerras, Lamia, et al.
Published: (2016)

Gesture bike: examining projection surfaces and turn signal systems for urban cycling
by: Dancu, Alexandru, et al.
Published: (2015)

Gesture bike: examining projection surfaces and turn signal systems for urban cycling
by: Dancu, Alexandru, et al.
Published: (2015)

A falling of the veils: turning points and momentous turning points in leadership and the creation of CSR
by: Hemingway, Christine A., et al.
Published: (2018)

Advancing Environmentally Conscious Machining
by: Ginting, Yogie, et al.
Published: (2015)

Effect of Machining Conditions and Phosphorus Content in Nano-Precision Machining of Electroless Nickel
by: Pramanik, Alokesh, et al.
Published: (2003)

Polyol esters as thinner and biolubricant additive for synthetic-based drilling fluid
by: Kania, Dina
Published: (2019)

Propaganda and persuasion: political discourse and the negotiation of power and authority in Yorkist and early Tudor England
by: Wheddon, Rebecca
Published: (2024)

Development of dry film lubricants for highly loaded contacts
by: Barman, Kanika
Published: (2016)

Improving the management of inventory in the Rolls-Royce Energy Aftermarket Business
by: Palmer, John
Published: (2011)

Railway network resilience
by: Meesit, Ratthaphong
Published: (2019)

Synthesis of jatropha biolubricant using sodium methoxide as catalyst
by: Gunam Resul, Mohamad Faiz Mukhtar
Published: (2012)

Biodegradation of phenanthrene and pyrene using bacteria isolated from used vehicle lubricant-contaminated soil
by: Darma, Umar Zubairu
Published: (2017)

Analisa ke atas minyak pelincir / Razak Awang … [et al.]
by: Awang, Razak, et al.
Published: (1997)

Oil film behaviour in hydrodynamic lubrication of journal bearing / Mohamad Ali Ahmad
by: Ahmad, Mohamad Ali
Published: (2014)

Surface texturing on dry-lubricated transmissions and power systems to deliver better performance and simplified systems in aerospace engineering
by: Ding, Liang
Published: (2021)

The Use of Bills of Quantities in Construction Projects - An Australian Survey
by: Davis, Peter, et al.
Published: (2004)

Elastohydrodynamic Analysis of Rolling Line Contact Using Boundary Element Method
by: Onsa, Mahmoud Hassan
Published: (2001)

Formulation, performance evaluation and prediction of bio-lubricant for journal bearings / Diyar I. Ahmad
by: I. Ahmed, Diyar
Published: (2014)

Cannot write session to /tmp/vufind_sessions/sess_3r5rqnbeei37devj7bo22t2kr6