Effect of Machining Velocity in Nanoscale Machining Operations

QR Code

Effect of Machining Velocity in Nanoscale Machining Operations

The aim of this study is to investigate the generated forces and deformations of single crystal Cu with (100), (110) and (111) crystallographic orientations at nanoscale machining operation. A nanoindenter equipped with nanoscratching attachment was used for machining operations and in-situ observat...

Full description

Bibliographic Details
Main Authors:	Islam, Sumaiya, Ibrahim, R., Khondoker, N.
Format:	Conference Paper
Published:	2015
Online Access:	http://hdl.handle.net/20.500.11937/36582

Similar Items

Machine learning at the nanoscale
by: Gordon, Oliver Miles
Published: (2022)

Modeling the effect of velocity saturation in nanoscale MOSFET
by: Tan, Michael Loong Peng
Published: (2006)

Modelling of nanoscale MOSFET performance in the velocity saturation region
by: Tan, Micheal Loong Peng, et al.
Published: (2007)

The dependence of saturation velocity on temperature, inversion charge and electric field in a nanoscale MOSFET
by: Saad, Ismail, et al.
Published: (2010)

Machining conditions effect to machining temperature and forces in orthogonal machining of bone
by: Kurniawan, Denni, et al.
Published: (2013)

Psychological impact of noise exposure among machine operators and non-machine operators in construction sites in Perak, Malaysia
by: Kee, Heng Yik
Published: (2019)

Psychological impact of noise exposure among machine and non-machine operators in construction industry
by: Kee, Heng Yik, et al.
Published: (2019)

Characterization Of Machining Defects In Wood Planing Operation
by: Farrokhpayam, Saeid Reza
Published: (2010)

Modification, Performance and Adaptation of Manually Operated Transplanting and Seeding Machines for Lowland Paddy
by: Islam, Md. Syedul
Published: (1998)

Nanoscale in photocatalysis
by: Wang, Z., et al.
Published: (2017)

Nanoscale Potentiometry
by: Bakker, Eric, et al.
Published: (2008)

Development of cut to length machine using programmable logic controller with human machine interface
by: Mashori, Sumaiya, et al.
Published: (2020)

Machining and Tool Wear Mechanisms during Machining Titanium Alloys
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Optimization of Roughing Operations in CNC Machining for Rapid Manufacturing Processes
by: M. Nafis, O. Z., et al.
Published: (2014)

The importance of reliability of machine on operational improvement : a case study
by: Juliana, Md Nor
Published: (2016)

An improved stator flux estimation in steady-state operation for direct torque control of induction machines
by: Idris, N. R. N., et al.
Published: (2002)

Effect of Machining Conditions and Phosphorus Content in Nano-Precision Machining of Electroless Nickel
by: Pramanik, Alokesh, et al.
Published: (2003)

Machine Parameter Optimization For Wire-Electric Discharge Machining
by: F. R. M., Romlay, et al.
Published: (2008)

Machine-to-machine communication: an overview of opportunities
by: Amodu, Oluwatosin Ahmed, et al.
Published: (2018)

Machining cost in conventional and hot machining: comparison and modelling
by: Elhadie, Mohamed, et al.
Published: (2011)

Considerations on the effects that core material machining has on an electrical machine's performance
by: Al-Timimy, A., et al.
Published: (2018)

Effect of operating parameters on the minimum fluidisation velocity of an inclined fluidised bed
by: Taib, Mohd. Rozainee, et al.
Published: (2003)

Nanoscale Investigation of Metamorphic Processes
by: Tacchetto, Tommaso
Published: (2022)

Nanoscale Isotopic Dating of Monazite
by: Fougerouse, Denis, et al.
Published: (2020)

On the crystal growth of nanoscale schwertmannite
by: Loan, Mitch, et al.
Published: (2005)

Design and performance test of a compressed air operated reciprocating machine
by: Abdul Aziz, Mohammad, et al.
Published: (2019)

Evaluation of flyrock phenomenon due to blasting operation by support vector machine
by: Amini, H., et al.
Published: (2012)

Improving Process Operations Using Support Vector Machines and Decision Trees
by: Jemwa, G., et al.
Published: (2005)

Computational inteligence in optimization of machining operation parameters of ST-37 steel
by: Golshan, Abolfazl, et al.
Published: (2013)

Effects of machining characteristics on electric discharge machine using different electrode materials
by: Mohd Khairul Anuar, Mohd Idris
Published: (2008)

Effective parallelisation for machine learning
by: Kamp, Michael, et al.
Published: (2017)

Sustainable Machining of Aerospace Material
by: Boswell, Brian, et al.
Published: (2013)

Design and development of a hybrid machine combining rapid prototyping and CNC milling operation
by: Amanullah, A.N.M., et al.
Published: (2017)

Advancing Environmentally Conscious Machining
by: Ginting, Yogie, et al.
Published: (2015)

Development of an Automated Selection System for Cutting Tools and Machining Parameters of Milling Operations
by: Goay, Lay Nee
Published: (2005)

Effects Of Polarity Parameter On Machining Of Tool Steel Workpiece Using Electrical Discharge Machining
by: Mohamed Reza Zalani, Mohamed Suffian, et al.
Published: (2010)

Performance of Cryogenic Machining with Nitrogen Gas in Machining of Titanium
by: Thet, Thet Mon
Published: (2011)

Machine vision for the measurement of machining parameters: A review
by: Abdul Wahab, Hashmi, et al.
Published: (2022)

Optically excited nanoscale ultrasonic transducers
by: Smith, Richard J., et al.
Published: (2015)

Novel approaches to the fabrication of nanoscale devices
by: Balakrishnan, Nilanthy
Published: (2015)

Cannot write session to /tmp/vufind_sessions/sess_vrr1l8904982spqrtafdid2qk1