3-D Numerical modeling of joint spacing and orientation effects on TBM cutters

QR Code

3-D Numerical modeling of joint spacing and orientation effects on TBM cutters

Bibliographic Details
Main Authors:	Sharifzadeh, Mostafa, Iranzadeh, A.
Other Authors:	Shahriar
Format:	Conference Paper
Published:	n/a 2007
Online Access:	http://hdl.handle.net/20.500.11937/36261

Similar Items

Comparison between 2D and 3D Numerical modeling of joint spacing and orientation effects on TBM cutter
by: Iranzadeh, A., et al.
Published: (2009)

Three dimensional numerical modelling of joint spacing and orientation effects on rock cutting process by a single TBM cutter
by: Sharifzadeh, Mostafa, et al.
Published: (2009)

Evaluation of load on TBM shield and segments using continuum-discountinum 3D numerical modeling
by: Sharifzadeh, Mostafa, et al.
Published: (2007)

A study of unusual TBM disk cutters wears in Karaj-Tehran water conveyance tunnel
by: Farokhnia, M., et al.
Published: (2008)

TBM Tunneling in adverse rock mass with emphasis on the TBM Jamming accident in Ghomrud water transfer tunnel
by: Sharifzadeh, Mostafa, et al.
Published: (2006)

Gas Ground Risks and Geological investigations for TBM Tunneling in Iran
by: Zarei, H., et al.
Published: (2011)

Selection of rock TBM based on geotechnical hazards mitigation
by: Shahriar, K., et al.
Published: (2006)

EPB-TBM Tunneling in Abrasive Soil Tehran Metro Tunnel Line 7, Iran
by: Amoun, S., et al.
Published: (2015)

Geotechnical risk assessment based approach for rock TBM selection in difficult ground conditions
by: Shahriar, K., et al.
Published: (2008)

Soil abrasiveness for EPB-TBM along Tehran metro tunnel line 7, Iran
by: Amoun, S., et al.
Published: (2015)

Influence of fault and crushed zones on TBM jamming in Ghomroud water transfer tunnel
by: Sharifzadeh, Mostafa, et al.
Published: (2007)

Numerical study of the behaviour of jointed tunnel lining
by: Barzegar, M., et al.
Published: (2015)

Difficulties in TBM Tunneling in adverse rock mass with Case study (Ghomrud water transfer tunnel)
by: Sharifzadeh, Mostafa, et al.
Published: (2006)

Effects of Joint Spacing on Static Bearing Capacity of Rock Foundations in the case of Punching Failure
by: Sharifzadeh, Mostafa, et al.

Bearing failure modes of rock foundations with consideration of joint spacing
by: Imani, M., et al.
Published: (2012)

3D Numerical Analysis of Coupled Stress – Flow in Rock Masses
by: Sharifzadeh, Mostafa, et al.
Published: (2007)

Numerical and Analytical Hydraulic Characterization of a Horizontal Single Joint Based on Radial Flow in Water Pressure Test
by: Karbala, M., et al.
Published: (2009)

A motorized cutter
by: Misron, Norhisam, et al.
Published: (2011)

Spider Grass Cutter
by: Zahar, Mohd Muzaffar, et al.
Published: (2020)

Investigation into the impacts of rock/cutter interface geometry on drilling response of PDC cutters
by: Doshvarpassand, Siavash
Published: (2017)

Multi-Scale joints roughness characterization using wavelet and shear modeling
by: Sharifzadeh, Mostafa, et al.

A hybrid finite element and surrogate modelling approach for simulation and monitoring supported TBM steering
by: Ninic, Jelena, et al.
Published: (2017)

Numerical Analysis Of Tbm Tunnel Behaviour And Support Under High Stress Rock Masses In Pahang-Selangor Raw Water Transfer Tunnel
by: Heyam Hussein, Shaalan
Published: (2019)

Finite volume numerical analysis of joint geometry effect on grout velocity changes with variable viscosity under unsteady turbulent flow regime
by: Sharifzadeh, Mostafa, et al.
Published: (2009)

Numerical analysis of the effect of fracture normal and shear stiffness on inflow into tunnel
by: Sharifzadeh, Mostafa, et al.
Published: (2007)

Evaluation of the hydraulic aperture of a rock joint using wavelet theory
by: Mehrishal, A., et al.
Published: (2013)

A Review of Hydromechanical Coupling Properties of Rock Joint
by: Sharifzadeh, Mostafa, et al.
Published: (2008)

Design and fabrication of motorized cutter prototype
by: Mohamad Ruzaini, Mohamed Ibrahim
Published: (2013)

Geometric modeling of 3D woven preforms in composite T-joints
by: Yan, Shibo, et al.
Published: (2017)

Ultimate bearing capacity of jointed rocks as homogenous media
by: Fahimifar, A., et al.
Published: (2010)

Automated grass cutter using voice recognition
by: Muhamad Salihin, Nasir, et al.
Published: (2021)

Smart cutter bantu pekebun kelapa sawit
by: Zahrom, Basir
Published: (2012)

Development of automatic control oil palm cutter
by: Abdul Rahim, Rahimi, et al.
Published: (1999)

Pemotong e-cutter mudahkn kerja mencantas
by: Sinar Harian
Published: (2018)

Design and improvise of high reach wire cutter
by: Esam, Asrizam, et al.
Published: (2022)

Upper Bound Solution for the Bearing Capacity of Submerged Jointed Rock Foundations
by: Imani, M., et al.
Published: (2012)

A bonded particle model for analysis of the flaw orientation effect on crack propagation mechanism in brittle materials under compression
by: Manouchehrian, A., et al.
Published: (2014)

3D numerical models for reinforced concrete components.
by: Jaafar, Mohd Saleh, et al.
Published: (2011)

Complex Networks on a Rock Joint
by: Ghaffari, H., et al.
Published: (2009)

Numerical Simulation of Gas Storage Caverns in Qom Region
by: Sharifzadeh, Mostafa, et al.
Published: (2006)